CNBM Polycrystalline Solar Panels for Pipeline Projects

Ref Price:
Loading Port:
Shanghai
Payment Terms:
TT OR LC
Min Order Qty:
1 pallet
Supply Capability:
10000000 pallet/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:



CNBM Polycrystalline Solar Panels for Pipeline Projects

CNBM Polycrystalline Solar Panels for Pipeline Projects

CNBM Polycrystalline Solar Panels for Pipeline Projects


Characteristics:

I.Solar Cell : High efficiency crystalline solar cell. Even if under the weak light, the solar module can produce maximum power output.
II.Tempered glass (toughened glass): Anti-reflecting coating and high transmission rate glass increase the power output and mechanical strength of solar module.
III.EVA and TPT: Using high quality EVA and TPT to prevent destroying and water.
IV.AI frame: Without screw, corner connection. 6 holes on the frame can be installed easily.
V.Junction box: Multi function junction box with water proof.
VI.Long lifetime:
25 years; Less power decrease.
VII.Good performance of preventing from atrocious weather such as wind and hails.
VIII.Resisting moisture and etching effectively, not effected by geology.
IX.The certificate issued by international authority: UL, TUV, IEC, VDE, CE.
 

Quality and Safety

1. Rigorous quality control meets the highest international standards.

2. High-transmissivity low-iron tempered glass, strong aluminium frame.

3. Using UV-resistant silicon.

4. IS09001/14001/CE/TUV/UL  

Warranties

1. 10 years limited product warranty

2. 15 years at 90% of the minimal rated power output

3. 25 years at 80% of the minimal rated power output

Technical date :

ITEM NO.:

Poly 156*156 cell ,60pcs . Power range from   230Wp-260Wp

Maximum Power(W)

230

235

240

245

250

255

260

Optimum Power Voltage(Vmp)

29.4

29.5

29.7

30.1

30.3

30.5

30.7

Optimum Operatige Current(Imp)

7.83

7.97

8.08

8.14

8.25

8.37

8.48

Open Circuit Voltage(Voc)

36.7

36.8

36.9

37.1

37.3

37.5

37.7

Short Circuit Current(Isc)

8.52

8.59

8.62

8.65

8.69

8.73

8.78

Solar Cell:

156*156 Poly

Number of Cell(pcs)

6*10

Brand Name of Solar Cells

Polycrystalline Cell

Size of Module(mm)

1650*992*40/45/50

Cable & Connector Type

Pass the TUV Certificate

Frame(Material Corners,etc.)

Aluminium-alloy

Back sheet

TPT

Weight Per Piece(KG)

19.5KG

FF (%)

70-76%

Junction Box Type

Pass the TUV Certificate

Tolerance Wattage(e.g.+/-5%)

±3%, or 0-3%

Front Glass Thickness(mm)

3.2

Temperature Coefficients of Isc(%)

+0.04

Temperature Coefficients of Voc(%)

-0.38

Temperature Coefficients of Pm(%)

-0.47

Temperature Coefficients of Im(%)

+0.04

Temperature Coefficients of Vm(%)

-0.38

Temperature Range

-40°C to +85°C

Surface Maximum Load Capacity

5400Pa

Allowable Hail Load

23m/s ,7.53g

Bypass Diode Rating(A)

12

Warranty

90% of 10 years, 80% of 25 years.

Standard Test Conditions

AM1.5   1000W/ 25 +/-2°C

Packing

carton or pallet

1*20'

14 Pallets / 316pcs

1*40'STD

25 Pallets / 700pcs

 

CNBM Polycrystalline Solar Panels for Pipeline Projects

CNBM Polycrystalline Solar Panels for Pipeline Projects


FAQ:

Solar panel refers either to a photovoltaic (PV) module, a solar hot water panel, or to a set of solar photovoltaic modules electrically connected and mounted on a supporting structure. A PV module is a packaged, connected assembly of solar cells. Solar panels can be used as a component of a larger photovoltaic system to generate and supply electricity in commercial and residential applications. Each module is rated by its DC output power under standard test conditions, and typically ranges from 100 to 320 watts. The efficiency of a module determines the area of a module given the same rated output – an 8% efficient 230 watt module will have twice the area of a 16% efficient 230 watt module. There are a few solar panels available that are exceeding 19% efficiency. A single solar module can produce only a limited amount of power; most installations contain multiple modules. A photovoltaic system typically includes a panel or an array of solar modules, an inverter, and sometimes a battery and/or solar tracker and interconnection wiring.


I..Will you focus on the safety of the goods during transportation?

Yes, Safety of the cargo is the primary element that we would consider on transportation.

II..How would guarantee the quality will meet the requirements of your clients?

Before shipment, we will have inspection for each batch of goods.

III..What certificates do you have?

IEC,UL,TUV,CSA,etc.

IV..Can you do OEM according to clients’ requirements?

Yes, we have our own brand while we can provide OEM service.


Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Does It really cost that much to Install solar panels?
It depends on the number and size of the panels. The minimum charge for a small bungalow would be at least $20,000 labor and material.
Q:how many solar panels?
If he lives in a sunny area, he should contact a local solar installer about getting a grid-tied solar system to offset his electric bill. It's not necessary to supply all the electricity from solar. The system will work seamlessly right alongside grid electricity, and your father can choose whether to supply 20% of the electricity or 99% by sizing the system appropriately.
Q:2v vs 24v solar panel?
The choice of solar panel voltage comes down more to what the panels will be connected to. You're right that power can remain the same at the different voltages. Higher input (panel) voltages are sometimes used in inverter systems to reduce the effect of voltage draw-down. 2v panels (about 20v open circuit) work well for charging 2v batteries, connected in parallel, through a charge controller. For use of a grid-tie inverter, higher input voltages are sometimes used to reduce the effects of draw-down. You want to select and wire (parallel vs. series) your panels based on the input voltage requirement of the load, whatever it may be.
Q:solar panels and batteries?
If it pulls 9 amps continuously, that's 08 watts/hour or about 2.5 kwh/day. If it only pulls half that (does it cycle?) it's about .2 kwh/day. You only want to drain a lead-acid battery 50% or so, so you'll want a 5 or 2.5 kwh battery pack. A typical setup for the 5 kwh would be two L-6 batteries in series, and for the 2.5 kwh you could use 2 T-05 batteries in series. This does not account for days of cloud. If you regularly have cloudy days, size the battery pack for two or three days of use with no input (2-3 x the sizes given above). To charge them, you typically want panels that will charge your battery at least 5% of its capacity per hour (C/20). For 2 volt nominal panels that's 0 amps for the T-05 or 20 amps for the L-6 batteries. It's good to have more than that for battery life (it cuts down on what's called stratification), so you'll want probably 50-200 watts of panels for the T-05 and 300-400 for the L-6. You'll also need a charge controller. Peltier coolers are very inefficient. You'll save money by using a regular mini-fridge and an inverter. Most mini-fridges only draw 50 watts or so, so you're talking 600 watt-hours for a 50% duty cycle. This means two T-05 batteries will give you two days of use and you'll only need 20-50 watts of panel. DK
Q:Home solar electricity advice? Making the solar panels accessible?
Modern solar electric panels rarely fail. Because of this, if you would be installing them over a roof that only has a few years left on it, it would be better to redo the roof, first. In the unlikely event that a panel needs to be changed, this can be done in 30 minutes or so, because the panels are mounted on racks, with everything simply plugging together. I have never personally seen a solar installation go bad, but from what I hear, the inverter (a box that goes in next to your electric service panel) is usually what burns out after 5 years, assuming the install was done right in the first place. If you were to call roofers to repair your roof, they would somehow be able to get to your roof, by ladders, or a special truck. Solar installers use the same kind of equipment. They won't have a problem getting up there. A solar electric system is actually a very straightforward thing. No matter who installs it, if there is a problem, another installer should be able to diagnose and fix it.
Q:harbor freight solar panels ?
Unless things have changed in the past few years, their panels are amorphous silicon, and sharply decline in output after 6 to 2 months. The panels have no STC (standard test condition) rating, so the 5-watt panel is really more like 5 watts. And the warranty is very short - 90 days, compared to the 25-year performance warranty of any serious crystalline silicon panel. But if you have a fun little project that does not have to last, Harbor Freight is a convenient source.
Q:Are solar panels a viable option in IL?
Yes solar panels are a good way to save money. I know a friend of mine she has 2 solar panel she lives in IL.I i know she told me that this year she saved 500$ in electricity bills. Good luck!
Q:What are the supplies needed in a solar panel field?
Short answer.. alot. A solar field is a big undertaking, and you'd be better off going with a solar consultant. I found this site and would recommend their services as they offer consulting, and are pretty big into solar (or atleast in my area..)
Q:how many solar panels will i need?
you silly ! with Solar there is always room for error . you have to build it in to your numbers . solar is full of errors . So you should plan on producing at 3 times what you expect you will need . then you have enough .
Q:Solar Panel costs and sizes?
Good question I am uncomfortable doing my child's homework so I will not complete the assignment for you. I am also always willing to help. Having the kWh is a great start. You must also ask the question when you size a system is there any way to reduce this load. Each kWh that you do not have to produce saves significant cost to the system. Next what type of system grid tied or off grid the two systems will have very different size needs and overall cost. I googled PV system sizing and got the below link. at first glance I like it. You can do the same for system cost. I also included a trade link for your review factors in sizing system type amount of bill offsetting geographic location site location track mounted or fixed and more Should you need additional help you can email me I will not do your work for you but I can either verify it or point you in the right direction

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range