Q:Ok, bought this mower at an estate auction for next to nothing. It looks like its never been used. Previous owner ripped out all the wires to the ignition switch so it wouldn't sell I guess. It's the craftsman lt 1500. Model number 247.288812. It has the 17.5hp bs motor in it. Does anyone know the correct way the wires go to the switch? There are 3 red wires so its a bit unlike what im used to. Thanks in advance!

On my sears mower with an electric clutch the switch is wired like this. G terminal is a black wire to ground. B terminal is a red wire to the ammeter. S terminal is a white wire to a safety switch. M terminal has two black wires one to the ignition coil and the other to a safety switch. L teminal is a red wire to the alternator and a red wire to the PTO switch.

Q:Why does a thin wire melt and a thick wire glow when put up to the terminals? Explain in terms of resistance and current. Thanks=]

Everything has a temperature at which it will melt. Every conductor also has a resistance, which is just like it sounds, a wire sort of resists the electricity passing through it by heating itself up. If a wire's resistance causes it to heat up so much that it melts, either the wire is too thin, or there is too much current passing through it, or both. A thicker wire can handle the same current without heating up so much that it melts. Sorry I don't have any formulas for you, but I think you should understand it now.

Q:How can u do a wire transfer? Is there anything extra that is needed to do this? Are you able to make a wire transfer from your home computer?

Most people go to the bank and arrange for wire transfer from there. You will need to have the funds to wire, the account where you want it transfered to. it is possible, but it would have to be prearranged.

Q:I have a 98 RS Eclipse (420a) and i would like some opinions and recommendations for spark plug wires. Who makes the best or very good wires for my engine??

Buy the stock wires. Make sure there is no oil on the old wires or you will need to replace the valve cover gasket and the 4 plug tower seals that are inside the valve cover. The motor came with Champion plugs, don't use Bosch.

Q:wiring has ceramic poles

This is one time I'd say life was much more important than the savings of heat and cooling. Your wiring is too old, probably brittle for any kind of activity up there. Just get some new wire and install it before messing with the insulation. Then if you have enough left over install what insulation you can.

Q:my speaker makes a fuzzy or static noise while the scene has high or low sound. I cut my wire in half because I bought a subwoofer and we didn't get the wires with it. So I cut it. After all I didn't need the wire for the subwoofer. Could my speakers make such noises because of cutting a wire?

I have no idea what you did. Which speaker(s) makes a static noise? You cut your wire in half. Which wire? Is your subwoofer wired to the speaker outputs or the SUB OUT on the receiver? Did you splice this wire or simply trim it, strip the ends and plug it into the receiver speaker outputs and the terminals on a speaker? What are you powering these speakers and subwoofer with? A receiver or an all in one HTIB unit? The best way to get good answers with any question is to provide as many details as possible - model numbers and the conditions under which the problem occurs. Details please.

Q:I need the wiring diagram for the factory radio of a 2008 ford explorer. i need to know which wires are for the back speakers so i can connect my Hi-Lo converter to it!? thanks

I believe this is what you are looking for, or should help... 2008 Ford Explorer Car Stereo Installation Instructions Car Radio Battery Constant 12v+ Wire: Blue/Red Car Radio Accessory Switched 12v+ Wire: Green/White Car Radio Ground Wire: Black/Blue Car Radio Illumination Wire: N/A Car Stereo Dimmer Wire: N/A Car Stereo Antenna Trigger Wire: N/A Car Stereo Amp Trigger Wire: Violet/Red Car Stereo Amplifier Location: N/A Car Audio Front Speakers Size: N/A Car Audio Front Speakers Location: N/A Left Front Speaker Positive Wire (+): White Left Front Speaker Negative Wire (-): White/Brown Right Front Speaker Positive Wire (+): White/Violet Right Front Speaker Negative Wire (-): White/Orange Car Audio Rear Speakers Size: N/A Car Audio Rear Speakers Location: N/A Left Rear Speaker Positive Wire (+): Brown/Green Left Rear Speaker Negative Wire (-): Brown/Yellow Right Rear Speaker Positive Wire (+): Brown/White Right Rear Speaker Negative Wire (-): Brown/Blue

Q:Im wiring my pioneer deh x3600ui to my pontiac grand am gt 2002 directly without a factory harness. Any diagrams out there i can use? The red wire on my pioneer is for the ignition but i cant find that wire on the pontiac.

if u cant find a diagram u can always check the speakers for the colors of the wires and then just try to get a hold a cheap little voltage meter like the one below just to find ur ground, remote, and battery wire.

Q:But I want to switch it and wire the red ceiling wire to the black fan wire and the black ceiling wire to the black/white fan wire so that the particular switches work the way I want them to. Is this ok, to switch them?

Black wire on the fan is for the fan motor, red wire in the fan is for the light, the white wire is the neutral wire. So if you do want to switch the light off and on you have to tie red wire to the switch and the black wire can be tied to the hot at the ceiling box so you can control the fan with the chain only. If you have one switch leg in your circuit then you cannot do anything but switch them both if you tie them together. I think I am understanding what you are saying here. White Alyse ties to white Black is for the fan motor and the red is for the light. If you have three wires in the switch then you can tie them the same way color to color. Hope this has not confused you You can email me if you need further help

Q:hi can anyone help i am currently building a 50cc scooter up from scratch i have most parts but ive started on the wiring does anyone know where i can get a wiring diagram also what wire recharges the battery from the magnetic pickup thanks

Here okorder /