It can be applied to refineries,petrochemical industry, coal chemical industry, cryogenic engineering, water supply factory, sea water desalination factory, heat supply and air-conditioning system,etc.
- Q:When the car runs neutral, does the oil pump work?
- If the manual models can be linked to neutral way but now the car is EFI even idling is not fuel-efficient if automatic car driving process is completely not linked to the gap automatic models of the space is just in the car and trailer when used only
- Q:The van is out of order. What's wrong with it? Can it make a noise?
- The oil pump is broken directly not oil. Also the valve sound somewhat sound feeling. You put the lid with the oil well pump apart to see if bad head above is not oil. But also holding tile. Direct locking.
- Q:What is the influence of insufficient oil supply in the oil pump?
- Increase the load on the engine and damage the engine
- Q:How do you install the pedal motor pump?
- Put the unit on the foundation with anchor bolts, between the base and the base, and use a pair of wedge pads.Release the axle shaft and place on the pump shaft and base with a level gauge. Adjust the level of the machine by adjusting the wedge pad and tighten the anchor bolts properly so as not to move around.Correct the concentricity of the pump shaft and the motor shaft, and allow the deviation of 0.1 mm on the outer circle of the axle shaft; two the clearance of the coupling plane shall be guaranteed 2~4 mm, and the clearance shall be uniform, and the tolerance shall be 0.3 millimeters.After connecting the pipeline and determining the direction of the motor rotation, then coupled with the coupling, and then check the concentricity of the shaft.In the actual test run 2~3 hours after the unit, for final inspection, if there is no adverse phenomenon, that the installation of qualified. Check the temperature and vibration of the bearing during the test run.During installation, all holes in the unit shall be covered to prevent debris from falling into the machine.In order to prevent the sundries from entering the pump, the filter shall be installed on the newly installed pipeline. The effective cross section shall be 2-3 times larger than the cross section of the suction pipe.However, the oil pump rarely fails, generally as long as the opening of the cylinder head, see more fresh oil or start the engine, there is oil jet, indicating the normal operation of the oil pump.
- Q:Accord 2 is timing, how about the oil pump?
- The pump also has a black spot on the point, even after a good bit and two black spots, a black spot on the point on the crankshaft, the two point of the oil pump is point, how many chains count on both sides, there is several section of the chain tensioner the!
- Q:How does the c4l determine whether the oil pump works? The oil lamp is on
- Hello This needs to be removed for inspection. If you don't understand, you can ask again. Wish you a happy life! [
- Q:The oil pump is not working well. What about the engine?
- Engine lubrication is not enough, it may damage the engine cylinder caused by high temperature
- Q:How tight is the screw for the car engine oil pump?
- There is a kilo on the general screw.
- Q:JMC 462Q engine does not go to the cylinder head, where is the oil pump located?
- You can't fix it by yourself.1, remove the valve compartment cover, you can see the rocker shaft, loosen the top of the middle fixed screws.2 you can blow it up in a high pressure air pump, clear it up, start the engine, and spray the oil outward.3, also can use steel wire (about 50cm long, rough 1mm or so, can reach that hole), to dredge, must exceed 25mm (cylinder head height) just go.4 or more can not work, and finally only remove the cylinder head.The 5 reason is that the cylinder pad (oil hole) is blocked by carbon deposits, and the engine oil can not reach the rocker arm.
- Q:My motorcycle two pedal 50, the oil pump has broken down, would you please add some bottle cap oil to the gas tank?
- You just add 2T oil directly to the gasoline tank. If the smoke is too big, add some more gasoline. If you don't smoke, add some more oil. Try to add a little less, because with it, for fear of inadequate lubrication, easy to scratch. The increase is easily broken a spark plug.
Our main products are all kinds of centrifugal pumps, displacement pumps and vacuum pumps, such as oil pumps, multi-phase pumps, single stage and double suction centrifugal pumps, horizontal split case pumps, multistage pumps, axial-flow pumps, mixed flow pumps, petrochemical pump and submersible pumps. Besides, our company also manufactures electric motors and sells electric motors, building materials, indoor decoration materials, civil electric equipment, devices and instrumentation, as well as exports our mechanical and electric products.
1. Manufacturer Overview
|Annual Output Value
||US$5 Million - US$10 Million
||59.00% Mid East
8.00% North America
8.00% Southern Europe
5.00% Eastern Asia
2.00% Southeast Asia
2.00% Western Europe
2.00% South America
2.00% Central America
2.00% Northern Europe
2.00% Eastern Europe
2.00% South Asia
2.00% Domestic Market
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
||51% - 60%
|No.of Employees in Trade Department
||Above 100,000 square meters
|No. of Production Lines
||OEM Service Offered Design Service Offered Buyer Label Offered
|Product Price Range
||High and/or Average