Chemical Passage Pump

Ref Price:
Loading Port:
Shanghai
Payment Terms:
TT or LC
Min Order Qty:
1 unit
Supply Capability:
1000 Sets Per Month unit/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Application:
It can convey the followings:
Chemical pulp which contains particles with diameter 1-8mm and less than 10%.
Salt slurry in soda and inorganic saltsOre pulp, mother liquor, seed crystal, decreased pulp, bentonite in metallurgy.Green mud, white mud, liquor relief, lime milk liquor in paper-making industryVarious intermedium, lactic acid, citric acid and fermenting liquor in fermentation industryWastewater in environmental protection and various industries.

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Bending machine, oil pump motor abnormal sound, what's the matter?
First, the hydraulic oil is not enough, will cause abnormal sound of the pump, check the amount of oil enough;Two, hydraulic oil dirty plug, oil suction port filter will cause abnormal sound, and oil cylinder, motor and other components of the work is not easy, in this case, wash the filter, and filter hydraulic oil or replace hydraulic oil;Three, the pump is damaged, the inner surface of the stator vane pump will wear a different sound, internal plunger piston pump will damage the abnormal noises and vibration of hydraulic system badly, the stress of this situation would not be stable, may be due to a hard object inside the hydraulic oil in the pump caused by card;Basically, these three situations.
Q:Will it clog up the oil pump by cleaning the engine oil which is strong enough to clog up the oil circuit?
Not recommended, if you want to deal with the best in time to repair the engine oil, the remaining half after adding detergent, appropriate to start the engine, but don't let the engine run continuously, repeated ignition immediately stop, the three stop 5 minutes during the three times, then stop for 1 hours, began to disassemble the bearing replacement of oil with high pressure gas to clean up, and then the parts are cleaned, the abnormal wear or exceed the wear limit of a replacement, beginning of assembly, assembly of lubricating parts with clean oil, oil filter assembly, oil filter oil filling. Start OK.The use of cleaning function of the engine oil will lead to dirt in the oil pipe to fall off, plug the oil on the part of the small hole, exacerbated by the need for lubrication parts of the abnormal wear and tear, serious machine scrapped. The loss outweighs the gain。I have seen the use of this detergent containing oil, after the use of the whole machine scrapped, the landlord carefully.
Q:Where is the oil pump installed?
There are two positions: one is mounted on the lower plane of the cylinder (also called the crankcase), and the two is at the front end of the crankshaft
Q:What is the function of the oil pump?
Keep the oil pressure down and keep the oil circulating while the engine is running
Q:What about the oil leakage of automobile oil pump?
If the oil pump is broken, replace it, if it is a rubber pad, change the cushion.An oil pump in a lubricating system that forces the oil from the oil pan to the engine moving parts. Used to increase the pressure of the oil and to ensure a certain amount of oil.
Q:What is the difference between an oil pump and a gear pump?
The oil pump and the gear pump all play the lubrication role, the engine oil pump is delivers the engine oil each to lubricate the part, but the gear pump is 2 or more gears, when works, gives him the fuel injection
Q:How do you install the pedal motor pump?
How to dismantle how old
Q:Automobile engine oil pump does not leak pressure, which causes oil seal ring to leak seriously. What is the trouble?
Automobile engine oil pump with crank, when the engine speed of pump oil is high, therefore need a pressure relief valve to keep the oil pressure of the main oil channel, the excess oil drain back to the oil pan, if the oil pump pressure relief valve failure, no pressure relief will lead to the oil pressure is too high, will be oil lattice sealing collopse. If the pressure relief valve normally open, it will cause oil pressure is too low, will burn bearings and the like.
Q:How much does the engine oil pump service cost?
Hello, dear, now the possibility of maintenance is very small, basically the replacement, as to the price should see what the car, different car prices are not the same
Q:Motorcycle not oil, oil pump work well, oil road is not blocked, how to check?
If no oil, the first to check without cylinder plug, hit by electricity whether oil, if not, the oil pump idling, first check the oil, if the oil pump is normal, it is broken, oil pump is self-priming pump, can be suspended in the oil, air formed by its own tic, low pressure, make the oil upstream. If the low pressure zone leaks or the low pressure does not form, there is no oil.
Our main products are all kinds of centrifugal pumps, displacement pumps and vacuum pumps, such as oil pumps, multi-phase pumps, single stage and double suction centrifugal pumps, horizontal split case pumps, multistage pumps, axial-flow pumps, mixed flow pumps, petrochemical pump and submersible pumps. Besides, our company also manufactures electric motors and sells electric motors, building materials, indoor decoration materials, civil electric equipment, devices and instrumentation, as well as exports our mechanical and electric products.

1. Manufacturer Overview

Location Hunan,China
Year Established 2006
Annual Output Value US$5 Million - US$10 Million
Main Markets 59.00% Mid East
8.00% North America
8.00% Southern Europe
5.00% Eastern Asia
2.00% Africa
2.00% Oceania
2.00% Southeast Asia
2.00% Western Europe
2.00% South America
2.00% Central America
2.00% Northern Europe
2.00% Eastern Europe
2.00% South Asia
2.00% Domestic Market
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port SHANGHAI,GUANGZHOU,DALIAN
Export Percentage 51% - 60%
No.of Employees in Trade Department 6-10 People
Language Spoken: English, Chinese
b)Factory Information  
Factory Size: Above 100,000 square meters
No. of Production Lines Above 10
Contract Manufacturing OEM Service Offered Design Service Offered Buyer Label Offered
Product Price Range High and/or Average