ceramci foam filter for aluminum industry
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 pc
- Supply Capability:
- 10000000 pc/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Specifications
Alumina circle ceramic foam filter
1.Even aperture, high porosity, proper sinter
2.Metal mesh to prevent secondary pollution
Alumina circle ceramic foam filter
The product, adopted good portiforium foam and high purity ceramic , effectively removes non-metal solid mixture from aluminium and aluminium alloy fusant.
Advantages:
even aperture, high porosity, proper sinter, high strength of anti-flexing and anti-compression, effective filtering.
It is widely applied to the aluminium fusant filter equipment of continuous casting, half-continuous casting, gravity casting, and low pressure casting.
Ceramic foam filters are different from aperture specifications from 10 to 45ppi, with different sizes and shapes.
Besides the general specification ,we can offer the product according to the customers requirements.
Form A Ceramic foam filter capability
Thickness
mm
Aperture
PPi
Volume intensity
g/cm3
Tortuous intensity in normal temperature
N/cm2
Pressure resistence intensity
in normal temperature
N/cm2
Pressure resistence
intensity
in high temperature
N/cm2
Refractory
temperature
Air discharging
capability
cm3/g
Porosity
%
15-100
10-45
0.35-0.45
≥38
≥80
≥45
≥1800
≤5
≥85
- Q:Excuse me, what's the reason that all ceramic filters do not attract ore?
- Vacuum system failure, no vacuum or vacuum can not meet the requirements. Should check the vacuum pump and vacuum piping, distribution head, ceramic plate, such as failure or leakage.
- Q:How can I avoid the backwash pressure in the production of ceramic filter?
- The backwashing system of ceramic filter is usually made up of water inlet, water inlet, pressure gauge, water filter and filtered water pressure gauge, and then connected to the inside of ceramic filter. Such as the discovery of ceramic filter recoil pressure became smaller or even no recoil pressure, you can carefully observe the surface of the ceramic filter plate is wet or ceramic filter plate wear without water injection at the discharge point, investigation and the reasons for the following aspects:Is the water inlet pressure or normal?How about the sealing performance of the water filter? Does the filter element need to be replaced?Is the recoil system piping (metal pipe, ceramic filter plate, connecting pipe, etc.) broken, leaking or dripping?Is the distributor valve properly installed and is it worn?Are there any cracks in the ceramic filter plate?Is the pressure gauge broken?The most likely reason is 1, 2, two, the best water should not be too dirty, filter should be replaced regularly. I hope the answer can help you.
- Q:What about the leakage of the ceramic filter static and dynamic sealing points?
- The filtrate pump works to drain or recycle the water that has been pumped out. 6 、 cleaning system work, cleaning system includes backwashing (water pump pressure or height difference pressure), acid liquid (metering pump, automatic acid injection), ultrasonic (ultrasonic work), etc.. 7 、 control system and other electrical systems. In addition, the filter cake which is absorbed and dried on the ceramic filter plate is unloaded automatically by the scraper and then falls on the belt conveyor, and is conveyed to the concentrate storage yard by a belt conveyor. Other questions about ceramic filter, welcome to chat with me or look at my head
- Q:What are the functions of honeycomb ceramic filters?
- High quality and high density straight hole mesh, the product has high heat resistance and impact resistance properties of cast high fever temperature, design straight hole to guarantee the balance between strength and flow, effectively remove impurities and slag particles, the mechanical properties of casting, the surface quality and the qualified rate of products is greatly improved.
- Q:What is the reason that ceramic filter does not absorb mineral powder?
- One is leakage, two is no liquid output or output weakness, pressure is too low, cleaning effect is not good, the pressure is too large, will cause damage to the filter plate and reduce the slurry concentration. The recoil pressure is regulated by the pump loop valve and the pressure regulating valve.
- Q:Ceramic filter in vacuum pressure enough, the ceramic plate does not suck pulp, what is the reason for analysis?
- The filtrate is not discharged smoothly.The filtrate can not be discharged in a timely and smooth manner, the new filtrate can not be sucked out, and the filtrate can not be continuously sucked out, so that the filter cake can not be adsorbed on the ceramic plate.
- Q:Principle of chemical engineering drum vacuum filter, the faster the speed, the less the amount of filtrate obtained per turn, the more the amount of filtrate obtained per unit time?
- In unit time, the more turns of the drum, the greater the centrifugal force, the greater the rate of filtration in unit time, that is to say, the amount of filtrate in unit time is moreRotating drum vacuum filter, the greater the speed, the greater the filtration rate, but the shorter the time each turn, the amount of each filtrate will be reduced
- Q:The vacuum degree of the ceramic filter is normal and the cake water is large
- The concentration, particle size and mud content of the raw materials are not suitable for or due to changes, which are no longer suitable for dehydration using ceramic filters
- Q:How many degrees does the ceramic filter melt?
- You should say clearly what ceramic you useHowever, as a melting furnace or filter medium, alumina products are the most versatile, but also silicon carbide, corundum, mullite, spinel and so on. They use very high temperatures.
- Q:The ceramic filter suddenly did not smoke, and later he was all right. What's the reason?
- Ceramic filter is mainly ceramic filter plate and vacuum system, ceramic filter plate is mainly product size of ceramic plate is a new, different manufacturers of different sizes; the vacuum system can be gradually investigation vacuum components and pipelines.The ore concentration, fineness and the concentration distribution in the slurry tank are different.A ceramic filter is composed of a plurality of system, more prone to such an unknown problem, fortunately: good!
1. Manufacturer Overview |
|
---|---|
Location | |
Year Established | |
Annual Output Value | |
Main Markets | |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | |
No.of Employees in Trade Department | |
Language Spoken: | |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
ceramci foam filter for aluminum industry
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 pc
- Supply Capability:
- 10000000 pc/month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Related keywords