Q:Can I use a standard 12 volt power cable on an Elmo projector?

Possibly on the BoxiT-200 that takes 12 to 19 volts at 3 amps, positive center. Read the printing on user manual, it gives the requirements. Most other Elmo projectors are plugged into an ac outlet.

Q:I need 600W of power for my new computer, but all I have is 2 300W, 20-pin power supplies. What I'm wondering is if I can combine the 2 20-pin connectors and turn them into 1 24-pin connector?

comput... repair las vegas

Q:10KV cable is directly from the nearest substation led to the power distribution room, how some people say that from the transformer can not understand what the meaning of more

Low-voltage power cable, also known as: low-voltage power cable. The voltage rating is 0.6 / 1KV. National Standard No .: GB / T-2008. The voltage rating of the control cable is 450 / 750V. National Standard No .: GB / T9330-2008. The voltage rating of these two cables, the country has a clear standard. Can not be changed.

Q:Hey guys,I am going to build a PC around gaming soon, and i was wondering, how many sata and power cables am i going to need for the build, i can't seem to find it anywhere. By that i mean, will i have to buy any extras? I do not know how many come with the mobo and/or PSU.

You only really need one SATA cable, for your HDD/SSD. Even then there are some hard drives that don't take it. Usually, a hard drive comes with the cable/strip included in the box.

Q:Printer is powered on cables are securely connected printer has ink and paper printer is installed as network printer on all clients computers and other users are able to print to the printer except me? what should i do so i can print

This sort of problem can happen with networks. Assuming the network has been set up correctly you can try a few things. It might be the sequence of switching things on and logging on. Try logging onto your computer AFTER printer is switched on. Also you can try not logging onto the network - I have had that work as well. I had 2 computers on a network that were always temperamental. Also check there are not too many users on the network, the printer can count as one user.

Q:i have a modular power supply i lost my cables moving out of my old house. so can any one tell me where i can get new ones to my power supply:

I don't think you can, really... Modular power supplies come with cables, they are not one size fits all, every brand and even every model might have different cables and plugs. Contacting the manufacturer will be your best bet, but it might not be worth it, might as well just buy another power supply, it's only another $45 shipping and all.

Q:So i left my xbox on over night (i know i know) and during the night there was either a power outage or surge, cuz all the electronic clocks had been reset. So i went to my xbox, and the light on the power cable box was red and my xbox wouldnt turn on. I havent tried unplugging it yet cuz the wires are behind my tv and a pain in the *** to get to, but i have a feeling this wont help.do i need to get it repaired?

The power brick is shot. Same problem happened to me. Best solution is to call xbox support and ask for a replacement. They'll ship one to you,the only problem is that sometimes they will charge you and sometimes they won't.

Q:The voltage level of the cable is how much the number of high and low voltage cables

Color line, HDMI cable, S-terminal line of the three transmission video signal (HDMI can also transmit audio signal); coaxial line is the transmission of audio signals

Q:I have a Dell Optiplex 790 SFF, I need a replacement power cable, on the manual it says for power: 240W, 1259 Btu/hr, 100 Vac to 240 vac, 50hz to 60 hz 3.6A. I contacted Dell and they said they have a power cable for it, the Dell 5120P cable which is 125 V 10A. Now my concern is with the 10A vs the 3.6A listed on the manual, should I be concerned?

no it will be fine, the maximum power needed as you state is 240W the replacement power cable is 125V 10A=1.25Kw so the power cable is grossly overated HTH David

Q:You have not connected the power cable to your video card. Please refer to the 'C settings started guide' for proper hardware installation.

It okorder /