Car tyre wheel Pattern 606 for super fashion and great quality

Ref Price:
Loading Port:
Qingdao
Payment Terms:
TT OR LC
Min Order Qty:
500 set
Supply Capability:
6000 set/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

 

No.606 details:

 

Size ETCBHoleP.C.DFinish
20X8.515-3072.6-1085/6114.3-139.7BLACK W/ MACHINE FACE
22X9.515-3872.6-1085/6114.3-139.7BLACK W/ MACHINE FACE
24X9.520-3072.6-1085/6114.3-139.7BLACK W/ MACHINE FACE

 

 

1) Lighter than tube wheels

2) Better cooling performance in longdistance and high speed driving

3) Bigger external diameter

4) High speed lowering tyre termperature can reduce wear resistance prevent tyre-shoulder seperation


Production Procedure:

1) Casting Machine Melting & Full Heat Treatment

2) CNC machine CNC made in Taiwan

3) Painting Line Full automatic Painting

4) Quality Control Certifications : JWL.VIA Japanese Standard

   Impact fatigue testing

   Bending fatigue testing,

   Radial run out testing

   Dynamic balance testing.

   Air-tightness testing

 

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:rear wheel drive cars?
Hey you, hope thanksgiving went well!. To answer your question, rear wheel has some benefits while front wheel also is beneficial. Rear wheel drives have more horse power to the wheel, but they also lose torque because of the drive shaft (longer shaft= less power to axle), but to compensate for this loss, they have invented some unique methods to deliver torque and increase power efficiency. They have reduced the gearing in the rear transaxle, and added slip differential to limit the transfer of energy to both rear wheels equally.Now front wheel drives have a very short transaxle, that transfers energy to the wheels with very little loss of energy. This makes them proficient, and less parts moving means less friction, therefore the engine works less. Most vehicles today are front wheel drive, except trucks and sports cars. But if you want fast power, rear wheel delivers that, but at a cost in gas$$$. Plus they will have more problems that are more expensive to fix.......hmmm sounds like front wheel is more better in a lot ways, but when you put the pedal down and feel the seat press up against you as the G's climb, rear wheel has it down. Talk to you again, and good luck finding the right car for you. Bye =Jesse=
Q:What is the model of the mountain bike in the movie "The wheel"?
And evil
Q:How can the history of the wheel change?
Unprecedented heart to create extraordinary people, extraordinary people to make extraordinary things, extraordinary things to change the extraordinary society, extraordinary social unrest extraordinary country, national turmoil, talented people, historical change, Weekends
Q:Rainy day train start, speed up, whether the wheel slip slip and rail friction? Can passengers be aware of it?
Train a section of the car is not tightly connected, the hook between the design of each other, parking or start before the hook will be forward, each compartment are not force each other. When the train started when the compartment between the buffer mechanism in a row to tighten the tight, the front at the same time each time only add a carriage, static friction is not so much thought. Sometimes at the start of the car at the beginning of the bar or sand. Imagine the structure of the chain. Each ring is pushed, starting from the first ring to pull the entire chain, not the whole movement at the same time, but between a section of the amount of tight pull forward.
Q:How many millimeters are the wheels of a road?
I was in the 2008, the wheels on the ground rolling a volume of the actual ride due to the tire after the load part of the deformation, may be smaller than this. My tire 700 * 23C, tire pressure 0.7MPa.
Q:The wheel community removes the chatting method
Click to open the [wheel community], and then click on the bottom of the [message]
Q:The car turns to why the two wheels have no corner turn
Because when the steering wheel outside the big round, the side of the wheel to take a small round. In order to avoid the additional resistance and excess wear of the car on the road when the car is turned, the steering system is required to ensure that all wheels are purely rolling when the car is turned. Obviously, this is only possible if the axes of all the wheels intersect at one point. In the figure, O is the steering center, we can see that the internal steering wheel deflection angle β should be greater than the outside steering wheel deflection angle α.
Q:Wheel spacers choice?
Sean is right, spacers screw up your suspension geometry. Your Geo will handle worse, not better. Look at it this way...does any car manufacturer have spacers in the original spec? No, they do not, there is a reason.
Q:When the car is fast, why does the wheel look like a turn
The wheels in every time interval, not only have time to turn the number of rounds of the integer, and also turned a little small half turn. When we see this changing picture, we do not think there is an integer number of turns here, but only the wheels are slowly turning (only a small fraction of each week). The results we feel that although the car go very fast, the wheel has turned very slow
Q:Kennedy, hard, light, round which is the wheel design requirements
The wheel is the design of the wheel, which is the rigid wheel that secures the inner edge of the tire, supports the tire and carries the load together with the tire. Will also be combined together with tires, rims and spoke collectively called wheels. By the wheels and tires two components composed of wheel assembly. A wheel is a rotating assembly that is loaded between a tire and an axle, usually consisting of two main component rims and spokes. The rim is a component that installs and supports the tire on the wheel, which is a bearing member between the axle and the rim between the wheels. In addition to the above-mentioned components, the wheels sometimes include wheels.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range