Detailed Product Description
-calcium silicate board
-fiber reinforced cement board
-ideal ceiling and wall partition material
Product technical parameters
Specifications and appearance
Length and width:±/3mm thickness:±/0.2mm Edge straightness:<2mm/m Diagonal line the maximum error:≤5mm
Right Angle,aren horn,quads chamfering45°Angle,aren45°Angle pour quads
Basic mechanical properties
No less than0.9g/cm3(state)In the EMS
High-strength fireprevention,Reduce the construction load,Add floor usable floor area Convenient installation
Longltudinal 7MPa Transverse 10MPa
Screws output pull
≤10%(state) In the EMS
Press GB8624-1997 to Judge,combustion performance doesn't burn A level product requirements
- Q:Why is the foam plate melted by the wire?
- You do not specifically say anything, rock wool sandwich panels, steel sandwich panels, or other. Such as the arc of the post to drink the United States and Taiwan is to pay attention to the high content of the glue is not used in hot places usually less use, must be used only shaped ceiling, because it can bend, other places do not use.
- Q:Roof insulation XPS board and EPS board What is the difference
- A: the construction site in line with the safety of the text through the raft flat Wo Chongguang state of platinum Kaiming construction measures requirements and norms. B: do not meet the requirements of safety and civilized construction measures, please rectification in xxx time in place
- Q:What are the materials used in building energy efficiency and why?
- The best effect is polyurethane spray or foam glass
- Q:What is the composition of XPS secondary foaming agent?
- Not necessarily, ah, according to the demand bar, if you Liangzhu pillars with pouring, stairs with the floor, you can not set up ramps, construction workers directly to the stairs
- Q:Can the roof insulation be filled with polystyrene board?
- From the model points: ① rigid waterproof casing points: A type, B type, C type, A type with steel pipe, B type for cast iron pipe and ductile iron pipe; ② flexible waterproof pipe points: A type, Type A is used in the interior wall of a building and type B is used in the facade of a building
- Q:Xps insulation board and extruded board which is good
- Landing scaffolding to build acceptance records Table 3-6-7 Project name: Engineering unit name: Urban construction company No. Acceptance project erection requirements test results 1 pole base solid level, there are drainage measures. Diverage 5cm thick plank, erected high > 7.55 m, 2 frame and pull knot joint spacing, horizontal, vertical distance to meet the requirements, pull the material meet the requirements, height> 12.6 meters are not allowed to use flexible connection 3 construction layer springboard double springboard banding point of not less than 4 points 4 scissors set not more than 9m set a scissors, angle of 45 ° ~ 60 °, from bottom to top continuous set, the height of more than 24m, in the foot of the corner and the middle along the vertical every 60 ° across the horizontal plane erected Slanting 5 scaffolding material scaffolding fastener steel pipe foot pipe diameter shall not be less than Φ48mm, wall thickness shall not be less than 3.5mm, no serious corrosion, crack, deformation, fastening torque 45 ~ 50N · m6 scaffolding width by design width 1) m erection 7 pole spacing vertical deviation of the vertical bar is not greater than the full length of 1 / 100H, vertical distance between the vertical design (1.8m) m set, deviation ± 50mm8 size horizontal horizontal horizontal vertical.
- Q:Wall paint brush and then do the whole wardrobe do not do waterproof can you
- Extrusion board (including EPS polystyrene insulation board and XPS extruded polystyrene board two) polystyrene foam is divided into expansive EPS and continuous extrusion XPS two, compared with the EPS sheet, XPS board is The third generation of rigid foam insulation materials, from the process it to overcome the complexity of the EPS board production process, with EPS board can not replace the superior performance. EPS such XPS (white crystal plate, extruded plate of a) is this:
- Q:The role of basement exterior wall waterproof polystyrene board
- Of course it is phenolic board. Polyphenylene board is not a development of the production of waste storage and fattening. Cement foam board is hard to say. Foreign developed countries use the most phenolic board and rock wool board.
- Q:Insulation board and holding plastic from the chemical reaction? Insulation board dip in the glass, with the structure of plastic line
- , to "plastic" approach in the pipe machine by extrusion processing Because of its light weight, corrosion resistance, beautiful appearance, no bad smell, easy processing, easy construction and other characteristics, in the construction project has been more and more widely used
- Q:How to cover the building shape to make the building insulation system better
- The connection between the pipe end connection and the steel ring The advantages and disadvantages of the connection: The connection of the pipe end is made by the butt welding method
We possesses more than 20,000 square meters modern and standard plant, over 250 employees, of whom professional and technical personnel occupying more than 30 keel professional and technical talents about 25 and the enterprise fully implements informationized and scientific management and possesses the domestically advanced production equipment currently. The specifications of our products are to meet the requirements of all customers, which made us developed fast and smooth among construction industry and enjoy good reputations in the world market.
We were honored to be the world's first research and development base of green sand rock, which attract many overseas building materials buyers to established long-term business relationship with us. Meanwhile, we have made a revolutionary breakthrough by obtaining numbers of invention patent. Eco-wallboards with well-equipped testing facilities and strong technical force are what we manufacture and sell at home and abroad. Our products series are made of inorganic facing material compounded with ceramic composited plate as a base, processed by our unique patented techniques, designed to provide excellent thermal and heat resistance, fire and sound insulation for a wide range of decoration requirements. They are widely applied in large public construction projects and interior decoration with graceful appearance and durability.
1. Manufacturer Overview
|Annual Output Value
Mid East 3.39%
Eastern Asia 4.64%
Central America 2.14%
Northern Europe 5.14%
Domestic Market 62.04%
||ISO 9001:2008;ISO 14001:2004
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
||81% - 90%
|No.of Employees in Trade Department
||10,000-30,000 square meters
|No. of Production Lines
|Product Price Range