Butterfly Valve Without Pin Ductile Iron DN500

Ref Price:
Loading Port:
Tianjin
Payment Terms:
TT OR LC
Min Order Qty:
5 set
Supply Capability:
50000 set/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Centerline structure,pinless double half shaft design.
Disc has two-way bearing, no installation direction requirements.
Non-backed replaceable seat with good performance and a longer working life.
Square and short neck for lable use and cost saving.
Easy installation, no need flange gasket.

 

SizeDN50mm-DN600mm
Design standardAPI609/EN593
End flangeDINPN10/PN16, BS4504PN10/PN16, ANSI class125#/class150#
Face to faceAPI609/EN558-1
Top flangeISO5211
BodyDuctile iron/Cast iron
DiscDuctile iron/CF8/CF8M/C95400/C95500
StemSS420
SeatEPDM/NBR/Viton/PTFE
ActuatorBare shaft/Lever/Gearbox and handwheel
CoatingEpoxy/Nylon/PTFE
PinWith out pin
Suitable mediumWater/Seawater/Sewage/Air/Foodstuff/Oil

 

 

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:What is the difference between the cut-off valve and gate valve, the general will use the cut-off valve instead of gate valve
Yes. Globe valves and gate valves are indeed common in certain piping and operating conditions.
Q:What kind of copper gate valve copper content standards, there are no national standards?
Please refer to: GB/T12225-2005 "general purpose valve, copper alloy casting technical specification" and GB/T 15116-1994 "die casting copper alloy"
Q:Gate valve z11h/y-16 what does that mean?
Product Name: internal thread gate valveItem number: Z11HProduct specification: DN15-50Product pressure: 1.6MPa-2.5MPaMaterial: cast iron, cast steel, stainless steelInternal thread gate valve nominal pressure 2.5Mpa, applicable temperature range -20-232-350, applicable medium: water, oil, gas and certain corrosive liquid (W.O.G), thread type G.NPT.BSPT.BSP.DIN259/2999.
Q:Gate valve type Z40Y, Z40H letters - what does that mean?
According to the provisions of the JB/T 308-2004 valve type programming method:Z== gate valve4== connection: flange0== structure: wedge type elastic RAMY== sealing surface material: hard alloyH== sealing surface material: Cr13 stainless steel
Q:How about the model of stainless steel gate valve?
Stainless steel gate valve is divided into 304 stainless steel gate valve, 316 stainless steel gate valve, 321 stainless steel gate valve. The expression is: Z41H-16P.
Q:What is the wedge type gate valve wedge is what mean
According to the gate can be divided into the form of parallel wedge type. (1) wedge type gate. Wedge type gate the sealing surface of a certain angle with the vertical center line of the gate, the size of angle depends on the medium temperature and diameter size. General medium temperature is higher, and the greater the inclination angle is bigger, in order to prevent the temperature change when the gate is stuck, unable to open. Wedge gate sealing than the parallel well.
Q:Analysis of the advantages of elastic seat sealing gate valve?
When the elastic seat sealing gate valve is closed, the sealing surface can be sealed only by the medium pressure, that is, the sealing surface of the flashboard is pressed to the valve seat of the other side only by the medium pressure to ensure the sealing of the sealing surface, which is self sealing.
Q:Internal screw current limiting gate valve (Tan Gang) PN5.0 DN15/ Phi 1 Rc1/2 what does that mean?
We did thatInternal thread current limiting gate valve (Tan Gang)Body material: carbon steelPressure rating: PN5.0 = 300LB American StandardNominal = DN15 = 1/2"Phi 1 = in the middle of the gate drilling a Phi 1 hole, so that in closing there will be a certain flow, that is, the minimum flow, that is, the current limit.Rc1/2 is thread, which is the connection
Q:Installation and operation instructions of knife gate valve
1. knife gate valve installation, check the valve cavity and sealing surface and other parts, not allowed to dirt or sand adhesion;2. bolts of connecting parts must be tightened evenly;
Q:Why does the fire hydrant box in the air defense area need to be added with gate valves?
when the envelope from the introduction of civil air defense, air defense should be set in the side of retaining structure; through the protection unit between the closed wall, should be installed in the pipe walls on both sides of the door closed;2 protection valve nominal pressure shall not be less than 1.OMPa;

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range