Butterfly Valve Without Pin Ductile Iron DN370

Ref Price:
Loading Port:
Payment Terms:
Min Order Qty:
60 set
Supply Capability:
50000 set/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Centerline structure,pinless double half shaft design.
Disc has two-way bearing, no installation direction requirements.
Non-backed replaceable seat with good performance and a longer working life.
Square and short neck for lable use and cost saving.
Easy installation, no need flange gasket.


Design standardAPI609/EN593
End flangeDINPN10/PN16, BS4504PN10/PN16, ANSI class125#/class150#
Face to faceAPI609/EN558-1
Top flangeISO5211
BodyDuctile iron/Cast iron
DiscDuctile iron/CF8/CF8M/C95400/C95500
ActuatorBare shaft/Lever/Gearbox and handwheel
PinWith out pin
Suitable mediumWater/Seawater/Sewage/Air/Foodstuff/Oil



Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:What are the differences between the gate valve and the cut-off valve?
The operating principle is different. The stop valve is an upward stem type, and the handwheel rotates and rises with the stem. Valve is hand wheel rotation, stem upward movement. Flow is not the same, the gate valve requires full open, the cut-off valve is not the same. The gate valve has no inlet and outlet direction requirements, and the cut-off valve has the required inlet and outletAt the same time, usually with the cut-off valve instead of gate valve, but the valve can also be used instead of cut-off valve. Valve sealing performance better, but the size is generally not large, the size of the gate valve can be done great.The main difference between them lies in:1, different structure, gate valve structure is more complex than the height, larger size, from the appearance point of view than the cut-off gate valve is short and high, especially the gate height space needs a higher open bar, the selection in the installation space under the condition of limited attention to.2, sealing surface, valve in the opening and closing valve and the valve seat surface always contact and friction between the sealing surface, and thus easy to wear, especially in close off the valve when the valve before and after the great pressure, sealing surface wear is more serious. And the valve once the valve is in open condition, it's seat and disc sealing surface between, not in contact,
Q:Why does the centrifugal pump start and stop in the case of closing the gate valve?
The centrifugal pump starts and stops in the case of closing the pump outlet valve. Start off the pump outlet valve is to reduce the starting current, stop when the pump is closed, the outlet valve is to reduce water hammer, prevent blade from bad.
Q:Gate valve DN65 what does that mean?
DN65 indicates that the valve bore is 65CM.The gate (gate valve) is a headstock ram, RAM direction of motion perpendicular to the direction of the fluid, valve can only be fully open and fully closed doors, discomfort pumpsparameters vary, usually 5 degrees is not high, medium temperature is 2 degrees 52'. To improve its manufacturability, make up for the deviation of the angle of the sealing surface during processing. This gate is called an elastic ram.
Q:The difference between gate valve and butterfly valve, as well as cut-off valve,
Valve is closed parts (RAM) along the vertical axis of the mobile channel valve in the pipeline, used primarily as a medium cut that open and close, generally do not have to do with traffic regulation, it can be used for low temperature and low pressure can also apply to high temperature and high pressure, and according to the different valve material for different media. In various types of valves, gate valve is the most widely used.Advantages: low fluid resistanceSmall torque required for opening and closingYou can use the ring road in which the medium flows in the two direction, that is to say, the medium is free of flowWhen fully open, the sealing surface is less eroded by the working medium than the cut-off valveThe structure is simple and the manufacturing process is betterThe structure length is shortDisadvantages: the overall size and opening height are larger, the space required for installation is also largerIn the process of opening and closing, there is relative friction between the sealing surfaces, and wear more easily, and even cause friction at high temperatureGeneral gate valve has two sealing pairs, to the processing, grinding and maintenance increased the number of difficultiesLong opening and closing time;
Q:What does gate valve do?
Valve in the pipeline can only be fully open and fully closed off, can not be adjusted and the throttle. Gate valve is a valve used in a wide range, generally more than 50mm caliber DN block device is selected it, sometimes cut off very small aperture devices are used to gate valve, gate valve is used as cut-off media, when in full flow through the whole, when the media is running a minimal pressure loss. Gate valves are normally used in situations where they do not need to be frequently opened and closed, and the gate is fully open or fully closed. Not used as an adjustment or throttling. For high speed moving medium, the gate can cause the vibration of the gate under the condition of partial opening, and the vibration may damage the sealing surface of the gate and the valve seat, while throttling will cause the gate to suffer the erosion of medium.
Q:What are the common standards for gate valves?
Is the gate valve opening and closing parts, RAM direction of motion perpendicular to the direction of the fluid, valve can only be fully open and fully closed, can not be adjusted and the throttle. The following common standards for Fujian Biaoguang valve for valve: design specification: JB/T 7746, API602 JB/T 7746, the length of the structure specification / thread socket factory test and inspection of JB/T1751/GB7306, ANSI: B16.11/B2.1: JB/T 9092, API598 pressure temperature: GB/T 9131, ANSI B16.34, MSS GB/T 12220 product ID: SP25 delivery specification: JB/T 7928
Q:What are the advantages and disadvantages of flat gate valves?
The advantage of flat gate valve is that the flow resistance is small, and the flow resistance is similar to the flow resistance of short valve. The flat gate valve with guide hole is installed on the pipeline and can be directly cleaned with the cleaner. As the gate is sliding on the two seat surface, the flat gate valve can be applied to the medium with suspended particles, and the sealing surface of the flat gate valve is actually positioned automatically. The seat seal surface is not subject to thermal deformation of the valve body. Moreover, even if the valve is closed in cold condition, the thermal elongation of the stem will not cause the seal to be subjected to overload. The length of the structure is much shorter than that of the ball valve, and it is easier to start. Light plate gate valve is more refined, but the effect is exactly the same.The disadvantage of flat gate valve is that when the medium pressure is low, the sealing force of the metal sealing surface is insufficient, so as to achieve satisfactory sealing. On the contrary, when the medium pressure is high, if the sealing surface is not lubricated by the system media or foreign media, often opening and closing may cause the sealing surface to wear too much. Another disadvantage is that the circular motion of the circular gate in the circular flow, only when it is at the valve closed position of 50%, this valve is more sensitive to flow control. Moreover, the gate will produce severe vibration when it breaks the high-speed and dense medium flow. The valve seat can also be throttled if the seat is made of a V - shaped opening and is tightly oriented to the gate.
Q:What is the difference between the cut-off valve and the gate valve?
When opening and closing, the valve core and valve seat sealing surface always contact and rub each other, so the sealing surface is easy to wear, the valve is close to shut down, the pressure difference between the pipe is very large, so that the sealing surface wear more serious.Gate valve and stop valve advantages and disadvantages:Valve is the advantages of small flow resistance, the media can flow in two directions, but there are tall, complex structure, sealing surface easy to wear shortcomings. The flow resistance of the gate valve is 3-5 times that of the gate valve. Open and close to shut down in order to seal the valve, the valve is completely closed when in contact with the sealing surface, the sealing surface wear is very small, because the flow of the main actuator with large valve should pay attention to adjust the torque control mechanism.
Q:What is the difference between Z41X gate valve and Z45X gate valve?
There is no difference in function. The two models are mainly made of different sealing materials,
Q:Generally, how big is the diameter of the installation flange plate gate valve?
Under normal circumstances:Flanged gate valves for piping over DN50,DN50 (below) can be made of wire or gate valves, or flanged gate valves (flanged valves or welded gate valves)

1. Manufacturer Overview

Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range