Butterfly Valve Without Pin Ductile Iron DN340

Ref Price:
Loading Port:
Tianjin
Payment Terms:
TT OR LC
Min Order Qty:
50 set
Supply Capability:
50000 set/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Centerline structure,pinless double half shaft design.
Disc has two-way bearing, no installation direction requirements.
Non-backed replaceable seat with good performance and a longer working life.
Square and short neck for lable use and cost saving.
Easy installation, no need flange gasket.

 

SizeDN50mm-DN600mm
Design standardAPI609/EN593
End flangeDINPN10/PN16, BS4504PN10/PN16, ANSI class125#/class150#
Face to faceAPI609/EN558-1
Top flangeISO5211
BodyDuctile iron/Cast iron
DiscDuctile iron/CF8/CF8M/C95400/C95500
StemSS420
SeatEPDM/NBR/Viton/PTFE
ActuatorBare shaft/Lever/Gearbox and handwheel
CoatingEpoxy/Nylon/PTFE
PinWith out pin
Suitable mediumWater/Seawater/Sewage/Air/Foodstuff/Oil

 

 

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Gate valve DN65 what does that mean?
Caliber 65, refers to the size of the gate valve, you want to buy it?
Q:What's the difference between a soft seal gate valve and a hard sealed gate valve?
Soft sealing gate valve is rubber seal, F sealed, hard sealing gate valve is the medium of particles.
Q:What valve is z45w gate valve?
Z = gate valve4 = connection: flange5 = structure form: dark rod typeW = sealing surface material: same as valve bodyDetails: JB/T308-2004 valve model preparation methods
Q:HVAC design, why is less than DN50 of pipe gate valve and cut-off valve,
I don't know why it was designed. Provide you with some information you refer to, I do not know if it works for you1, stop valve and gate valve are very expensive, more than DN50 can make a lot of money2, butterfly valve is only more than DN50, no small, there may be, but I almost can not see the market.3, like DN150, DN200 such cut-off valve, gate valve is very large, and the butterfly valve is relatively light, installation can save the cost of the block, the valve itself saves too much money.4, but most of the butterfly valve used for a long time are closed.
Q:Gate valve z11h/y-16 what does that mean?
Product Name: internal thread gate valveItem number: Z11HProduct specification: DN15-50Product pressure: 1.6MPa-2.5MPaMaterial: cast iron, cast steel, stainless steelInternal thread gate valve nominal pressure 2.5Mpa, applicable temperature range -20-232-350, applicable medium: water, oil, gas and certain corrosive liquid (W.O.G), thread type G.NPT.BSPT.BSP.DIN259/2999.
Q:What is the difference between the cut-off valve and the gate valve?
What is the difference between gate valve and stop valve?:Gate valve and globe valve structure is different, the valve structure for hand wheel, with the stem rotating together to do the opening and closing movement. Valve structure is rotating handwheel, stem do lifting movement. The flow is different, the gate valve requires full open or full closed state, the cut-off valve does not need. The valve has the flow direction requirements, and the gate valve has no inlet and outlet requirements!Sealing performance comparison:Valve length is shorter than the cut-off valve, higher than the cut-off valve, the valve should pay attention to the installation of high elevation. The gate valve can be tightly closed with the sealing surface by the pressure of the medium so as to achieve the effect of not leaking.
Q:Gate valve type Z40Y, Z40H letters - what does that mean?
According to the provisions of the JB/T 308-2004 valve type programming method:Z== gate valve4== connection: flange0== structure: wedge type elastic RAMY== sealing surface material: hard alloyH== sealing surface material: Cr13 stainless steel
Q:What is the difference between gate valve and gate valve? Is it the same valve?
The same, very few people call gate valve, all call gate valve.
Q:What is the wedge type gate valve wedge is what mean
It can be used on high pressure gate valve. Wedge gate and elastic wedge gate, gate and double gate. A, elastic ram. A circular groove is machined on the vertical bisector surface of the gate so that the gate plate has a certain elasticity. It is this elastic deformation, the gate is closed, the compensation gate sealing surface and the valve seat sealing surface between the wedge angle deviation, the arrival of good agreement, to ensure the sealing. Resilient gate valve sealing surface reliable. Applicable to a variety of pressure and temperature of small and medium-sized gate valve, requiring medium containing solid particles to less, in order to prevent congestion in the gate ring groove, affecting the flexibility of sealing.
Q:What is the difference between a flanged gate valve and a wire gate valve?
Flanged gate valves are flanged and must be welded to the flanges of the pipe, bolted together

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range