Butterfly Valve Without Pin Ductile Iron DN190

Ref Price:
Loading Port:
Tianjin
Payment Terms:
TT OR LC
Min Order Qty:
50 set
Supply Capability:
50000 set/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Centerline structure,pinless double half shaft design.
Disc has two-way bearing, no installation direction requirements.
Non-backed replaceable seat with good performance and a longer working life.
Square and short neck for lable use and cost saving.
Easy installation, no need flange gasket.

 

SizeDN50mm-DN600mm
Design standardAPI609/EN593
End flangeDINPN10/PN16, BS4504PN10/PN16, ANSI class125#/class150#
Face to faceAPI609/EN558-1
Top flangeISO5211
BodyDuctile iron/Cast iron
DiscDuctile iron/CF8/CF8M/C95400/C95500
StemSS420
SeatEPDM/NBR/Viton/PTFE
ActuatorBare shaft/Lever/Gearbox and handwheel
CoatingEpoxy/Nylon/PTFE
PinWith out pin
Suitable mediumWater/Seawater/Sewage/Air/Foodstuff/Oil

 

 

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:What type of valve does the butterfly valve D343X DN300 represent?
D- butterfly valve, 3- worm drive, 4- flange connection, 3- three eccentric, X- soft seal, DN300- nominal size is 300, the full name is 300 of the three eccentric butterfly valve, and I hope to help you.
Q:Butterfly valve common faults and treatment methods?
Three, summary:Only familiar with every detail of circulating water pump outlet valve and butterfly valve equipment, timely and thorough maintenance and strict debugging, to ensure the safety and reliability of equipment operation, to ensure the healthy and orderly operation of equipment.
Q:What is the meaning of the D341*5-10 / 16ZB1 turbine butterfly valve flange said?
Liu1964tg, this guy is right, don't know, don't mislead everybody
Q:What's the difference between cut-off valve, gate valve and butterfly valve? What's the difference in the working principle?
Stop valve is closed parts (valve) moving along the centerline of the valve seat, the valve stem to open or close the trip is relatively short, but very reliable cut off function, and because changes in the valve seat and the valve stroke is proportional to the amount of adjustment is also very suitable for convection.Check valve: also known as counter flow valve, check valve, back pressure valve or one-way valve, such valves are dependent on the flow of the pipeline itself flow force and automatically open and close, belonging to an automatic valveButterfly valve: it is a kind of valve which uses disc type opening and closing parts to turn back and forth about 90 degrees to open, close and adjust the passage of fluidGate valve is closed parts (RAM) along the vertical axis of the mobile channel valve in the pipeline, used primarily as a medium cut that open and close, generally do not have to do with traffic regulation, it can be used for low temperature and low pressure can also apply to high temperature and high pressure, and according to the different valve material is different in various media. The valve, the valve is the most widely used.
Q:Timing belt reason for bent valve?
Yes, unless you've left out a critical detail (such as getting water into a cylinder), the timing belt is the most likely explanation for your bent valve. It doesn't neccessarily mean the person who 'did' your timing belt buggered it up, it may have just slipped. The short-ish period between getting work done and the valve getting bent is a little suspicious, but slips happen, especially with belts (as opposed to chains and dual row chains). This puts you in a difficult situation. You may also want to inspect your valvetrain, piston face, and the bore of that cylinder for damage.
Q:Butterfly valve flow direction is single or two-way?
Hello, soft sealing butterfly valve is generally two-way flow, large bore with flow direction is one-way flow. Hard sealed butterfly valves are the same.
Q:What are the functions and uses of butterfly valves?
Butterfly valve is fully open to fully closed is usually less than 90 degrees, butterfly and butterfly stroke itself has no self-locking capability, in order to position the disc to install the valve stem on the worm gear.Using worm gear reducer, not only can the butterfly plate have self-locking ability, so that the butterfly board stops at any position, but also can improve the operation performance of the valve.
Q:Model specification for butterfly valves
Various classifications of butterfly valves1. classification by structure:(1) Central sealed butterfly valve(2) single eccentric sealed coal valve;(3) double eccentric sealed butterfly valve(4) three eccentric sealed stamp valve;
Q:D37A1X9-16CB1: what does this butterfly valve mean?
The model is composed of 7 units, the types of valves (gate valve Z, J, L, Q ball valve, throttle valve, check valve and H valve, butterfly valve, connection mode (D) internal thread 1 thread 2, welding flange 4, 6, 7, the clamp (0) electromagnetic transmission mode 1 solenoid valve, hydraulic, electric and hydraulic turbine are 2, 3, 4 and 5 gears, bevel gear, pneumatic hydraulic, 6, 7, 8, 9) pneumatic and hydraulic, electric, structure (straight or DC type 7,1 on behalf of the center plate, vertical type A (A) and LT X9) on behalf of a sealant is heat-resistant rubber, kg 16 kg, C represents the body material of carbon steel WCB, B1 on behalf of the valve plate is made of ductile cast iron plating)
Q:Is the pressure test of the centerline butterfly valve checked or checked?
The pressure test of the central butterfly valve is carried out at each station.Basis:1) GB/T12238-2008 flange and clamp connection elastic seal butterfly valveRules: butterfly valve must be carried out by factory inspection and testing, inspection qualified before leaving the factory.2) CJ/T 261-2007, butterfly valves for water supply and drainageRules: each product shall be inspected by factory and quality inspection department. After inspection, the product certificate shall be attached to the factory.Butterfly: also known as butterfly valve, control valve has a simple structure, can be used for low pressure pipeline valve switching control is closed parts (disc or disc) is a disk, around the valve axis to achieve the opening and closing a valve, the valve can be used to control air, water, steam, all kinds of corrosive media, mud, oil, metals and radioactive liquid media and other types of fluid flow. On the pipeline, mainly from cutting and throttling. Butterfly valve headstock is a disc shaped disc, in the valve body around its own axis of rotation, so as to achieve the purpose of opening or closing or regulation.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range