Butterfly Valve Without Pin Ductile Iron DN150

Ref Price:
Loading Port:
Tianjin
Payment Terms:
TT OR LC
Min Order Qty:
50 set
Supply Capability:
50000 set/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Centerline structure,pinless double half shaft design.
Disc has two-way bearing, no installation direction requirements.
Non-backed replaceable seat with good performance and a longer working life.
Square and short neck for lable use and cost saving.
Easy installation, no need flange gasket.

 

SizeDN50mm-DN600mm
Design standardAPI609/EN593
End flangeDINPN10/PN16, BS4504PN10/PN16, ANSI class125#/class150#
Face to faceAPI609/EN558-1
Top flangeISO5211
BodyDuctile iron/Cast iron
DiscDuctile iron/CF8/CF8M/C95400/C95500
StemSS420
SeatEPDM/NBR/Viton/PTFE
ActuatorBare shaft/Lever/Gearbox and handwheel
CoatingEpoxy/Nylon/PTFE
PinWith out pin
Suitable mediumWater/Seawater/Sewage/Air/Foodstuff/Oil

 

 

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:What's the difference between an electric two position control valve and an electric butterfly valve?
The electric butterfly valve belongs to a kind of electric valve and electric control valve. The main connection modes of electric butterfly valve are flange type and clip type. The main forms of electric butterfly valve are rubber seal and metal seal. The electric butterfly valve controls the switch of the butterfly valve through the power signal. The product can be used as the shut-off valve, control valve and check valve of the piping system.
Q:How to connect the signal butterfly valve?
Signal butterfly valve is divided into two, 1) single signal, that is, signal instructions open or shut in place, only reflects a state, 2) double signal instructions, that is able to reflect in place or in place.
Q:Water supply pipe gate valve and butterfly valve which good?
1. gate valve: also known as gate valve or gate, there is a valve in the valve flow direction perpendicular to the medium, adjust the height of the gate, you can adjust the flow of fluid. Valve advantages are small resistance, close tight, no water hammer phenomenon, widely used in a variety of liquid and gas shut-off valve. It also has some adjustment function, but when the part is opened, the gate is easy to be wetted by the fluid. When the fluid flows, it causes the shaking of the alarm board and the sealing surface is easy to wear. The drawback of the gate valve is that the structure is complex, the price is more expensive, it is difficult to repair, and the solid material is easy to deposit in the valve seat groove. Therefore, it is not suitable for the pipeline containing fiber or solid material in the fluid. Commonly used in the air, steam, oil medium pipeline, but also used as vent valve and low silk system valve.Gate valve is commonly used as one of the cut-off valve, mainly used to connect or cut off the medium in the pipeline, not applicable to regulating medium flow. Valve is suitable for pressure, temperature and caliber range, especially for medium and large diameter pipes.
Q:How to calculate the size of the manual butterfly valve?
I don't know what size you mean, and what about DN in diameter, such as DN125, which means 125 cm in diameter
Q:How can the flange butterfly valve be installed on the pipe?
Direction.Butterfly valve in theory can be installed in any direction, it is recommended that the horizontal installation of the valve shaft installation, so that both ends of the bearings will not be at the bottom (below), so as to avoid sediment in the media into the bearing.Inlet pipe configuration.There are water inlet side valve elbow, tee pipe fluid caused by bending and uneven distribution of the inflow valve, the drift will occur in the pipe, so it must be generated by the uniform drift disposed on both sides of the disc, so as to avoid uneven force on both sides of the disc, and may produce additional torque.
Q:The difference between gate valve and butterfly valve, as well as cut-off valve, what are their applicable conditions? Advantages and disadvantages?
Without strict conditions and advantages and disadvantages, of course, the equipment requires a relatively high degree of automatic control. I can check it out on Baidu.
Q:Fire, the signal butterfly valve flange connection or welding?
1, do a good job with flange.2, flange (Flange), also known as flange, flange plate or edge. A flange is a part that is connected between the pipe and the pipe, used for the connection between the ends of the pipe. It is also used for the flange on the entrance and exit of the equipment. It is used for the connection between the two devices, such as the reducer flange. Flange connection or flange joint means that the flange, the shim and the bolt are mutually connected as a group of three detachable sealing structures. Pipe flanges are flanges used for piping in pipe installations. They are used on equipment and refer to the entrance and exit flanges of the equipment. The flange is lined with bolts to secure the two flanges. Gaskets for gaskets between flanges. Sub threaded flange connection (threaded connection), flange welding flange and flange clamp. Flanges are used in pairs. Low pressure pipes can be made of wire flanges and welded flanges with pressures of more than four kilograms. Add a gasket between the two flanges and secure with bolts. Different pressure flange thickness is different, they use the bolt is also different. Water pump and valve, and in the pipe connection, these equipment parts of the equipment also made corresponding flange shape, also known as flange connection. Any connecting parts that are bolted and closed in the vicinity of the two planes are generally referred to as flanges, such as the connections of the ventilation ducts, which can be called flanges". However, this connection is only part of a device, such as flanges and pumps connected, it is not good to call the water pump flange parts". Relatively small, such as valves, can be called flanges".3, also known as welding: welding, melt, is a kind of heating, high temperature or high pressure way of metal or other thermoplastic materials such as plastic manufacturing process and technology.
Q:Butterfly valve switch direction respectively?
If it is not to sound from behind, from large to small if that is in the open.
Q:Which is better, the round two lobe butterfly valve?
The company has advanced sheet metal CNC processing line, strong technical force and strong production capacity. At present, the main products are: air outlet, air valve, muffler, fire damper, static pressure box, wind box, etc.. Especially round type double butterfly butterfly valve has obvious advantages.
Q:Butterfly valve D71X-10 and butterfly D371X-10 what is the difference?
One more 3 in D71X-10 stands for adding a worm gear to the valve. What are the same, the difference is driven by the handle into the drive, gear drive, worm gear drive for large caliber butterfly valve a little less, because the valve torque is big, big, hard to handle and can rotate, and if the worm, you can turn a few laps handwheel. If there are other questions, we can continue to ask questions, the city butterfly valve manufacturers

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range