Butterfly Valve Stainless Steel Threaded Directional on Hot Sale Made in China

Ref Price:
$50.00 - 3,000.00 / pc
Loading Port:
Tianjin
Payment Terms:
TT or LC
Min Order Qty:
100 pc
Supply Capability:
10000 pc/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

 

1. Manual Wafer Butterfly Valve Description

A butterfly valve is a valve which can be used for isolating or regulating flow. The closing mechanism takes the form of a disk. Operation is similar to that of a ball valve, which allows for quick shut off. Butterfly valves are generally favored because they are lower in cost to other valve designs as well as being lighter in weight, meaning less support is required. The disc is positioned in the center of the pipe, passing through the disc is a rod connected to an actuator on the outside of the valve. Rotating the actuator turns the disc either parallel or perpendicular to the flow. Unlike a ball valve, the disc is always present within the flow, therefore a pressure drop is always induced in the flow, regardless of valve position.

 

2.Main Features of the Manual Wafer Butterfly Valve 

a)Cast hole. Flange connection meet ANSI 125/150#   DIN PN10/16   BS4504 PN10/16 in the meanwhile.

 

b)Soft seat. Replaceable. Increase of service life.

 

c)Double half shaft without pin.

 

d) Square and short neck. Easy to stick scutcheon and cost saving.

 

3. Manual Wafer Butterfly Valve Images

 

Butterfly Valve Stainless Steel Threaded Directional on Hot Sale Made in China

Butterfly Valve Stainless Steel Threaded Directional on Hot Sale Made in China

 

4.Manual Wafer Butterfly Valve  Specification

 

 

Butterfly Valve Stainless Steel Threaded Directional on Hot Sale Made in China 

5.FAQ

 

1. What is manual wafer butterfly valve?

A: Wafer style is the more common of the two and is less expensive than the lug style. The wafer style butterfly valve is just about the standard. It ís so common that no one even bothers to use the word "wafer" when ordering a butterfly valve. It is taken for granted that if a butterfly valve is ordered, a wafer style will be received.

 

2. How about the Installation of the Wafer Style Butterfly Valve?
A: Butterfly valves are installed by inserting the valve between two flanges using bolts or studs and nuts to hold it all together. This type of installation, of course, makes it impossible to disconnect just one side of the piping system from the valve. That benefit is received using the lug style valve.

 

3. What is the working principle of manual wafer butterfly valve?

 A: A butterfly valve is from a family of valves called quarter-turn valves. In operation, the valve is fully open or closed when the disc is rotated a quarter turn. The "butterfly" is a metal disc mounted on a rod. When the valve is closed, the disc is turned so that it completely blocks off the passageway. When the valve is fully open, the disc is rotated a quarter turn so that it allows an almost unrestricted passage of the fluid. The valve may also be opened incrementally to throttle flow.

 

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Why use the pump outlet valve to adjust the flow rate?
With the advantages of the pump outlet valve adjustment, 1, you can control the pump outlet pressure, 2, you can control the motor current is not more than the process conditions, 3, control motor power, to ensure the normal operation of the pump.
Q:How are the types of valves classified?
Valve (Famen) is a control component in the fluid delivery system. It has the functions of closing, adjusting, guiding, preventing reverse flow, stabilizing voltage, shunting or overflow and releasing pressure.classificationFunction and use(1) cut off categories: such as gate valve, globe valve, plug valve, ball valve, butterfly valve, needle valve, diaphragm valve and so on. Cut off valve, also known as closed-circuit valve, stop valve, whose role is to connect or cut off the pipeline medium.Check valves, also known as check valves or non-return valves, check valves belong to an automatic valve, its role is to prevent the pipeline medium backflow, to prevent the pump and drive motor reversal, as well as the leakage of container media. Pump water off the bottom valve check valve also belongs to class.The function of the relief valve is to prevent the medium pressure in the pipeline or device from exceeding the required value so as to achieve the purpose of safety protection.Control valve, throttle valve and pressure reducing valve, its role is to regulate the media pressure, flow and other parameters.(2) vacuum type: such as vacuum ball valve, vacuum flapper valve, vacuum air charging valve, pneumatic vacuum valve, etc.. Its function is to change the direction of the air flow in the vacuum system, adjust the air flow rate, cut off or connect the vacuum system of the pipeline, and the component is called the vacuum valve.(3) special uses such as pigging valves, vent valves, drain valves, exhaust valves, filters, etc.. The exhaust valve is an essential auxiliary component in the pipeline system. It is widely used in boilers, air conditioners, petroleum, natural gas, water supply and drainage pipelines. Often installed in the commanding heights or elbows, etc., to exclude excess gas pipeline, pipe road to improve the use of efficiency and reduce energy consumption.
Q:How to quickly identify the types of valves?
The "Practical Handbook" valve design on the valve structure, with precision, surface roughness and typical design standard, the valve has hundreds of models, and continue to have a new valve, see a written one, is shorthand.Valves: valves (Valve) control the flow of fluid medium flow, flow, pressure, temperature and other mechanical devices, valves are the basic components of the pipe system. Valve fittings are technically similar to pumps and are often discussed as a separate category. Valves can be operated by hand or hand wheel, handle or pedal, or by control to change the pressure, temperature and flow change of fluid medium. The valve can perform continuous or repeated operations on these changes, such as a safety valve installed in a hot water or steam boiler. In more complex control systems, automatic control valves are required depending on external inputs (i.e., regulating the flow through the pipe to the changing setting points). Automatic control valve without manual operation, according to its input and settings, so that the valve accurately control the requirements of fluid medium. The valve according to the material is divided into cast iron valves, cast steel valves, stainless steel valves, chrome molybdenum steel, chromium molybdenum vanadium steel valves, valve, dual phase steel valves, plastic valves, non-standard customized valve material etc..
Q:How about the quality of FITOK valves?
It's made in China. It's also made of foreign brands!Swagelok, Hoke, Parker, these three are foreign brands!
Q:What are the most common types of valves?
From the controllable and uncontrollable division (personal opinions, according to our factory valves used to explain)1. hand operated: gate valve, globe valve, ball valve.2. control: single seat valve, two seat valve, ball valve (O ball, V ball), eccentric rotary valve, butterfly valve, diaphragm valve
Q:How big valves are used in a DN159 pipe?
Nominal diameter DN150 corresponds to the outer diameter of De159To say DN159 is wrong, because DN is the nominal diameter (diameter in the middle of the tube wall)De159 refers to the outside diameter (outside the diameter of the wall)DN39 should be DN32. Nominal diameter 32, outer diameter 39.
Q:What do you mean by the 16 bit coding of the valve type?
Not regular encoding. Regular encoding is usually 11 bit and sometimes 13-14 bit
Q:What should be checked before using the valve?
The valve must be tested before installationI. examination of documentsThe valve must check the quality documents before installation, the valve manufacturer should be nameplate, nameplate and the body should be the name of the manufacturer, valve type, nominal pressure, nominal diameter and logo, must comply with the "universal valve logo" GB 12220.Two, appearance inspection
Q:What are the production equipment in valve shop?
Machining equipment: CNC, universal car, milling machine, drilling machine (rocker arm drill), wire cutting, grinding machineTest equipment: valve test press according to the production of valve pressure, specifications, types of procurement.
Q:Internal structure of valve
The first question is basically the same, and you can understand that for the secondThe 3,4 problem, there are several seat connections, such as thread connection (threaded, the valve seat is connected with the valve), modular connection (such as adding the cage to a fixed seat, the crushed) as one of the body and there is (some welding). The valve seat must be fixed.The fifth question, you are right!

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range