Q:Should I connect the butterfly valve before and after the pump? Or gate valve?

This situation should use gate valveBecause it has the following advantages:1, the fluid resistance is small, the sealing surface by the erosion of small and medium Chong brush.2, opening and closing more effort.3, medium flow unrestricted, no disturb, do not reduce pressure.4. The shape is simple, the structure length is short, the manufacturing technology is good, and the scope of application is wide.Butterfly valve main deficiency is that it uses the pressure and temperature range is small.And poor sealing. Therefore, the gate valve should be preferred.Of course, there is also a multi-functional pump control valve is also very good, dedicated to the water supply system. Connection URL: (Reference), you can look at yourself, and I hope to help you.

Q:DN80 flange butterfly valve, DN80 flange butterfly valve DN80, flange butterfly valve DN80 what is the difference?

No, what's the difference?. It's not all the same.Flange connectionDN80 caliber butterfly valve. What's the difference?. Model and pressure. Materials are not ~!

Q:Butterfly valve common faults and treatment methods?

Three, summary:Only familiar with every detail of circulating water pump outlet valve and butterfly valve equipment, timely and thorough maintenance and strict debugging, to ensure the safety and reliability of equipment operation, to ensure the healthy and orderly operation of equipment.

Q:Fire signal butterfly valve what role?

Signal butterfly valve should be human action monitoring alarm, once closed, that is, to the system alarmYou ask the two time, I answer two times, you give two points

Q:1st where is my zone valve? I have an old Burnham gas baseboard heater2nd What do I do?My last resort is calling a proffesional.

if your sure its not the thermostat than the zone valve should be near the boiler in the copper line. Most valves have a flat lever that slides when it is powered up to open. You can open manually by sliding the lever

Q:Who was the first doctor to discover Pulmonary Valve Stenosis? Also, who was the first doctor to perform surgery for it? Please and thank you for your help.P.S. I have this condition.

1761 - Pulmonary valvar or valvular stenosis is one of the more common forms of congenital heart malformations and it has been extensively studied since the original description of pulmonary valve stenosis by John Baptist Morgagni in 1761. 1888 - Tetralogy of Fallot, first characterized by Dr.Etienne Fallot in 1888, is present in about 3000 children born each year in the United States. It is a combination of four heart abnormalities. Dodrill and his colleagues employed it with success for the open correction of a stenotic pulmonary valve in October 1952.

Q:My quot;check engine soonquot; light came on yesterday and soon after that I took it to the nearest Midas to have the diagnostic test run on it - they stated I needed an ERG valve. I have no clue what it is and was told that it could run $160. - $300. for my 1900 Astro van. what is an ERG valve? I have noticed that my van has a low humming sound when I'm driving it.

An egr valve is an exhaust gas recirculation valve, basicly it allows for exhaust gas to be routed into incoming air-fuel mix- it causes reduced emissions. They r expensive, know however that often when a diagnostic is run and egr is the read out alot of times its an O2 sensor(oxgyen sensor), the egr and O2 sensors work together so its hard for a computer to idenitify the exact prob, u can take ur van 2 an exhaust shop and have them inspect it. Which i highly recomend, that way u know 4 sure what the prob is. Good luk hope i helped!!!

Q:Do you use the straight stem butterfly valve in the fire fighting engineering?

Only the gate valve clearly rod and dark pole, butterfly valve classification is the clamp type and flange type, Zhengzhou butterfly valve factory, Mr. Zhao

Q:The difference between the directly buried gate and the flange valve and butterfly valve

Buried gate also called buried gate valve, valve can be directly buried underground, built without manhole, reduce road excavation area; small well maintained road and beautiful room can reduce the difficulty of construction, reduce project cost. The directly buried soft sealing gate valve is divided into two types: telescopic type and fine fixing type, wherein, the telescopic type is divided into metal type and plastic type. In the process of construction, the telescopic type can be adjusted arbitrarily according to the distance between the buried depth of the valve and the ground, and the micro adjustment can be adjusted on the spot. The directly buried gate valve has the advantages of long-term use, no leakage, no maintenance, etc., and can effectively avoid other people switching the valve and stealing the manhole cover at will.Flange gate valve is connected to the flange gate valve, this connection is the most common way.

Q:Not the cold and hot water shut off valves. The one with a tiny handle and it looks like a T. what does it do? should I mess with it?

Sounds okorder /