Butterfly Valve DN150 D373H-16C D343H-6C D343H-10C D343H-16C H343H-25C
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 10 unit
- Supply Capability:
- 500 unit/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Butterfly valve, also called the flap valve is a kind of simple structure of the regulator,
also can be used in low pressure pipeline medium valve butterfly valve in the switch
control the way work is closed a (disc or disc) is a disk, around the axis of rotation to
achieve a valve open and close, mainly in the line cut off and throttling effect.
Butterfly valve opening and closing is a disc-shaped butterfly plate, the body rotation
around its own axis, so as to achieve the aim of opening and closing or adjust.
Introduction to the
Butterfly valve, butterfly valve) : also called butterfly valve worm gear
Definition: open-close part for disc butterfly plate and a valve body axis rotate.[1]
Structure: mainly by the valve body, valve stem, disc and seal ring.The body is
cylindrical, short axial length, built-in butterfly plate.
Using range
Electric butterfly valve butterfly valve is suitable for the generator, gas,
natural gas, liquefied petroleum gas, city gas, cold hot air smelting, chemical
industry and power generation, environmental protection, such as, building
water supply and drainage engineering system of conveying a variety of corrosive,
non corrosive fluid pipe, used to adjust and block the flow of the medium.
Functional purposes
Pneumatic butterfly valve butterfly valve (English: butterfly valve) is to point
to shut down a (disc or disc) is a disk, around the axis of rotation to achieve
a valve open and close, mainly in the line cut off and throttling effect.Butterfly
valve opening and closing is a disc-shaped butterfly plate, the body rotation around
its own axis, so as to achieve the aim of opening and closing or adjust.Butterfly valve
fully open to the barrier is usually less than 90 °, butterfly valve and the adjustment
lever itself has no self-locking ability, in order to butterfly plate positioning, to add
worm gear reducer on the valve stem.The use of worm gear reducer, can not only
make the butterfly plate with self-locking ability, make the butterfly plate to stop at
any position, also can improve the performance of the valve.Industrial specialized
characteristic ability of high temperature butterfly valve, apply pressure range is higher also,
nominal valve size is big, the body is made of carbon steel, valve plate seal using metal ring
instead of rubber ring.Large high temperature butterfly valve USES the steel plate welding
manufacturing, mainly for the duct smoke and gas of high temperature medium.
- Q:Specifically an engine valve retainer.
- This Site Might Help You. RE: What if the function of a valve retainer? Specifically an engine valve retainer.
- Q:Butterfly valve sealing material has several?
- 9: H- stainless steel composite layerX3- ethylene propylene rubberX4- chloroprene rubberX5- nitrile rubberX6- abrasion resistant rubberX7- fluorine rubberX8- silicone rubberX9- heat resistant ethylene propylene rubberF- PTFE
- Q:Fire signal butterfly valve what role?
- Signal butterfly valve should be human action monitoring alarm, once closed, that is, to the system alarmYou ask the two time, I answer two times, you give two points
- Q:How is the lug butterfly valve connected to the flange?
- It is clip type butterfly valve.Connection way is to use butterfly flange flange.The sealing surfaces at the ends of the two rubber sealing rings are respectively butted with the welded flanges welded on the pipe; the two headed screws and the nuts are used for fastening.
- Q:What is the meaning of the D341*5-10 / 16ZB1 turbine butterfly valve flange said?
- D341 is flanged connection center plate butterfly valve under pressure 1.0MPa-1.6MPa ZB1 rubber soft seal
- Q:D37A1X9-16CB1: what does this butterfly valve mean?
- The model is composed of 7 units, the types of valves (gate valve Z, J, L, Q ball valve, throttle valve, check valve and H valve, butterfly valve, connection mode (D) internal thread 1 thread 2, welding flange 4, 6, 7, the clamp (0) electromagnetic transmission mode 1 solenoid valve, hydraulic, electric and hydraulic turbine are 2, 3, 4 and 5 gears, bevel gear, pneumatic hydraulic, 6, 7, 8, 9) pneumatic and hydraulic, electric, structure (straight or DC type 7,1 on behalf of the center plate, vertical type A (A) and LT X9) on behalf of a sealant is heat-resistant rubber, kg 16 kg, C represents the body material of carbon steel WCB, B1 on behalf of the valve plate is made of ductile cast iron plating)
- Q:For whatever reason, Mazda has made it next to impossible to change the PCV valve on the 929. I'm going to have to pull off the plenum and the passenger's side valve cover to replace a $2.00 PCV valve. Before I get too involved, I need to know the torque specs for the valve cover. Also, any other tips on this process would be greatly appreciated. Can I reuse the old valve cover gasket if it's still in good shape? Should I use any kind of sealant in addition to the gasket when I put it all back together? Thanks in advance, by looking at this motor, I can tell I'll have my work cut out for me (for a friggin $2.00 PCV valve, it's usually SO simple!). Like I said, any and all help is greatly appreciated.
- you do not torque valve covers down, buy a new gasket , I would get a good quality rubber one and some blue rtv sealer, clean any crap off the valve cover no glue no bits of gasket nothing, same thing on the head surface, glue the gasket on the valve cover, let it set, then carefully put it on, start with the bolts in the middle and work out finger tight all of them, then just snug the bolts down, dont crush the gasket, you can also use a light duty locktite to hold them in place, and often times old valve covers are warped, it is too your advantage to make sure its as flat as you can get it, or spend a few bucks a buy a new one. your choice, but snug the nuts down good with out crushing and bending the thin sheet metal of the valve cover.
- Q:How can one - way sealed butterfly valves and two-way sealed butterfly valves be distinguished?
- Two way hard sealing butterfly valve:Two way butterfly valve on the valve body usually does not indicate the direction of the media arrow sign, in the design of two-way sealing butterfly valve stem force is greater than one-way butterfly valve stem. The same diameter, pressure butterfly valve, two-way sealing butterfly valve rod diameter than one-way sealing butterfly valve stem diameter. At the time of installation, the butterfly plate can face or back the direction of the medium, without considering the flow direction of the medium.
- Q:My quot;check engine soonquot; light came on yesterday and soon after that I took it to the nearest Midas to have the diagnostic test run on it - they stated I needed an ERG valve. I have no clue what it is and was told that it could run $160. - $300. for my 1900 Astro van. what is an ERG valve? I have noticed that my van has a low humming sound when I'm driving it.
- If initially the codes confirmed that the EGR valve grew to become into defective and grew to become into no longer replaced this might smash the o2 sensor. whilst the EGR is caught open simply by fact of carbon strengthen the engine is taking in extra air it is coming from the blistered gases out of the exhaust and re burning them interior the process the EGR. The O2 sensor will examine this gases passing interior the process the exhaust and point out a lean mix of gasoline and could sign the ECM to strengthen the gasoline to the engine nsequently after a time of employing with mistaken mixtures the o2 sensor will fail. My suggestion is to change the EGR and the O2 sensor then highway try the vehicle.then have the codes rechecked. additionally if the engine isn't working mushy this might reason the transmission to act up.verify that the vacuum hose is linked to the modulator valve on the decrease back of the transmission. some transmissions have a working laptop or computer on a separate circuit interior the device and if the engine isn't working solid computer will p.c.. up the incorrect sign and transmission won't shift properly.. solid good fortune oh and the vehicle ECM or computer isn't your difficulty.
- Q:Which is expensive, butterfly valve?
- Gate valve and butterfly valve can not simply take the price there to compare, look at the actual design requirements of the project. General small caliber are selected by the valve, because of better sealing performance, service life is long, the maximum diameter of valve is usually choose to use the butterfly valve to the pipeline DN800800 above, because the valve is cheap, the price is only half of the large diameter valve. Also some pipes from the use of quality point of view, will choose the gate valve. How to use it, please mark the map
1. Manufacturer Overview |
|
---|---|
Location | |
Year Established | |
Annual Output Value | |
Main Markets | |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | |
No.of Employees in Trade Department | |
Language Spoken: | |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
Butterfly Valve DN150 D373H-16C D343H-6C D343H-10C D343H-16C H343H-25C
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 10 unit
- Supply Capability:
- 500 unit/month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products