Butterfly Valve DN100 D373H-16C D343H-6C D343H-10C D343H-16C H343H-25C

Ref Price:
Loading Port:
Shanghai
Payment Terms:
TT OR LC
Min Order Qty:
10 unit
Supply Capability:
500 unit/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Butterfly valve, also called the flap valve is a kind of simple structure of the regulator, 

also can be used in low pressure pipeline medium valve butterfly valve in the switch 

control the way work is closed a (disc or disc) is a disk, around the axis of rotation to

achieve a valve open and close, mainly in the line cut off and throttling effect.

Butterfly valve opening and closing is a disc-shaped butterfly plate, the body rotation 

around its own axis, so as to achieve the aim of opening and closing or adjust.

Introduction to the

Butterfly valve, butterfly valve) : also called butterfly valve worm gear
Definition: open-close part for disc butterfly plate and a valve body axis rotate.[1]
Structure: mainly by the valve body, valve stem, disc and seal ring.The body is 

cylindrical, short axial length, built-in butterfly plate.
Using range
Electric butterfly valve butterfly valve is suitable for the generator, gas, 

natural gas, liquefied petroleum gas, city gas, cold hot air smelting, chemical 

industry and power generation, environmental protection, such as, building

water supply and drainage engineering system of conveying a variety of corrosive,

non corrosive fluid pipe, used to adjust and block the flow of the medium.
Functional purposes
Pneumatic butterfly valve butterfly valve (English: butterfly valve) is to point 

to shut down a (disc or disc) is a disk, around the axis of rotation to achieve 

a valve open and close, mainly in the line cut off and throttling effect.Butterfly 

valve opening and closing is a disc-shaped butterfly plate, the body rotation around

its own axis, so as to achieve the aim of opening and closing or adjust.Butterfly valve 

fully open to the barrier is usually less than 90 °, butterfly valve and the adjustment 

lever itself has no self-locking ability, in order to butterfly plate positioning, to add 

worm gear reducer on the valve stem.The use of worm gear reducer, can not only 

make the butterfly plate with self-locking ability, make the butterfly plate to stop at

any position, also can improve the performance of the valve.Industrial specialized 

characteristic ability of high temperature butterfly valve, apply pressure range is higher also, 

nominal valve size is big, the body is made of carbon steel, valve plate seal using metal ring 

instead of rubber ring.Large high temperature butterfly valve USES the steel plate welding 

manufacturing, mainly for the duct smoke and gas of high temperature medium.

 


Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Butterfly valve general use occasions
Butterfly valveAlso known as butterfly valve, control valve has a simple structure, can be used for low pressure pipeline valve switching control is closed parts (disc or disc) is a disk, around the valve axis to achieve the opening and closing a valve, the valve can be used to control the flow of air, water, steam steam, all kinds of corrosive medium, mud, oil, metals and radioactive liquid media and other types of fluid. On the pipeline, mainly from cutting and throttling. Butterfly valve headstock is a disc shaped disc, in the valve body around its own axis of rotation, so as to achieve the purpose of opening or closing or regulation.
Q:Butterfly valve D71X-16 and D71X-16Q what is the difference?
D71X-16 can be ductile iron, stainless steel, carbon steel, and so onD71X-16Q can only be ductile ironIt's material that has special requirements. It seems like this
Q:Will A Stop Valve Switch Off Water In The Bathroom Only
Assuming that the stop valves are good, turning them off will stop the flow of water to the sink taps. To test them, turn on the water faucet at the sink, then turn off both stop valves. The water should stop coming out of the faucet. If it continues to drip, the stop valves are defective and should be replaced when you do the job. If this is the case you'll have to shut off the main water valve or a valve upstream of the stops to replace them. Good Luck
Q:What does the butterfly valve model d344h, d345h, d346h, d347h mean?
According to the international standard of the letters and numbers apart to explain D344H D is a unit of butterfly valve, two unit 3 is driving mode: turbine, three unit 4 connection: flange connection, four unit 4 Structure: seal type linkage, five unit H sealing material: Cr13 stainless steelD345H compare yourself to the above. Unit 5 four is a sealed, single eccentric structureD346H four unit 6 is an unsealed center vertical plateD347H four unit 7 is unsealed double eccentricIn general, there is only one difference between them: the structural form is different!
Q:unstick valves in 1988 volkswagon rabbit?
The only reason for a stuck valve is if it bent from a thrown timing belt. Sitting 4 years will not cause valves to stick usually, because there is always some oil leakage from the head, that prevents rust. How do you know the valve is stuck? Have you done a compression test, checked the valve clearance? When you say you take a wrench to manually unstick it, it would help to know what you mean, because there is no place to put a wrench that would help unstick a valve that was stuck. You need to tell us much more.
Q:The difference between vertical and horizontal butterfly valves in municipal water supply
Function is no difference, mainly the installation conditions are not the same, vertical valve shaft in the vertical direction, the valve well on the deep, horizontal valve shaft in the horizontal direction, the valve width to be larger, and the other is no difference
Q:Especially butterfly valve
Butterfly valve "opening - flow" curve in the flow of 25%-75%, that section is basically linear. That is, the opening of 40%, that flow is about 40%Butterfly valve opening degree of 0.5, should be opened 50%, that is, opening to 45 degrees;
Q:How to control the single acting pneumatic butterfly valve?
Single acting pneumatic butterfly valve can be divided into gas open type and gas closed type, which is usually called "normally closed" and "normally open". This is very critical. The single feature pneumatic butterfly valve is the biggest feature of its spring reset function, when the loss of gas or sudden failure, you can automatically restore the original state. So it's important to open the air or air this time.
Q:What are the advantages of butterfly valves?
D. sediments are not readily accumulated;The E. is compact and has little installation
Q:Valves in a I4 or V6 engine...?
Well a lot of valves signify that more air/gas is getting to the engine so it suggests a more powerful engine. So your car has 4 valves per cylinder. Now that's pretty much a standard number so most expensive cars don't really even talk about that. They mostly just advertise the displacement. You can't really tell the type of engine via the number of valves because it does vary by manufacturer. For example there could be a 16 valve V8 also also(2 valves per cylinder). There are some ratios that dont work like a 16 valve V6 because you cannot have 2.6 valves.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range