Burners for Reforming Unit and Prehydrogenation Heater

Ref Price:
Loading Port:
China Main Port
Payment Terms:
TT OR LC
Min Order Qty:
-
Supply Capability:
-

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

New types of Burners for Atmospheric & Vacuum Unit, Aromatic Hydrocarbon Unit and Disproportionation Unit, which are suitable for large-size Vertical Fired Heaters with longer tubes (Using for compound generation such as Atmospheric & Vacuum, Aromatic Hydrocarbon, Disproportionation,etc.), are designed and manufactured independently by Corporation. The flame of each Burner is powerful and high which matches with Fired Heaters. Combined oil and gas is used as fuel of most Burners which can use oil only or gas only or oil & gas together. Burners of this type can be used under the condition of natural draft of about 70Pa floor negative pressure or forced draft of less than 500Pa. The temperature of preheat air shall be less than 350℃ (more than 450℃ for special design).

Off-gas Incinerator Burner

Off-gas Incinerator Burners are often used to burn H2S from Acid Gas Incinerators and remove it finally. The temperature of the Burners shall be usually about 650℃, and required temperature shall be kept by adding compensation of fuel gas.

Ammonia Incinerator Burners are often used to burn acid gas and off gas contained ammonia, the flue gas after burning mixed with air will be discharged directly. The temperature of the Burners shall be usually about 1300℃ in order to remove NH3 in acid gas effectively, and required temperature shall be kept by adding compensation of fuel gas.

GROUP mainly produces the following products:

l  Refinery/chemical furnaces, incinerators, coal (liquid) chemical reformers

l  Waste heat boilers, thermal medium boilers

l  Class A1 /A2 pressure vessels

l  Reactors, Heat Exchangers & Towers

l  Oil tanks/accessories/mixers, alloy steel precision castings

l  Four classes of piping supports and hangers used in fired-electric/thermo-electric/nuclear electric power industries and dampers

l  Flue gas/air/coal powder duct and its attachments

l  Boiler ancillaries, water treatment devices and so on

GROUP obtains the following certificates:

l   Class A Certificate of Engineering Design

l   Design License of Pressure Vessel (Class A3)

l   Manufacture License of Pressure Vessel (Class A3)

l  Design & Manufacture License of Pressure Piping (Class A)

l  Manufacture License of Waste heat boilers (Class A), thermal medium boilers

l  ISO 9001:2000 Quality Management System

l  ASME U and ASME S

l  Enterprise Credit: AAA

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:How many kinds of industrial electric furnaces are there?
Industrial furnace according to the heating mode is divided into two categories: one is the fuel furnace, combustion heat with solid, liquid or gaseous fuel in the furnace for heating the workpiece; the second is in the furnace, the furnace converts electrical energy to heat the heat.
Q:What are the advantages of a vacuum furnace?
Energy consumption is lower than salt bath furnace. Modern advanced vacuum industrial furnace heating chamber is made of high quality heat insulation material and wall, which can concentrate electric heating energy into heating chamber with remarkable energy saving effect.
Q:Why does the burner of industrial furnace burn occasionally?
The general process for burner ignition, blowing furnace, electric spark ignition, solenoid valve, open the gas in case of delayed spark ignition, detection device detects the flame, the controller accepts signal so that the solenoid valve open, gas continuous normal combustion. However, if the ignition fails or the burner fires, the detector cannot detect the flame, which causes the solenoid valve to close and the burner flameout.
Q:How to use industrial furnace equipment?
The protection device of the exposed transmission department shall be installed with the correct installation position. The structure is reasonable. The wire rope pulley of the furnace car shall be intact and undamaged. All the pulleys and sprockets on the furnace are in good condition, without defects and flexible in rolling.
Q:Selection of heat preservation material for industrial furnace
Ceramic fiber blanket can be used.Ceramic fiber blanket color white, regular size, set fire, heat insulation, insulation in one. Free from any binding agent.
Q:What are the combustion equipments used in industrial boilers?
Main auxiliary equipment for general boilers:1. domestic appliances 2. civilian gas boiler 3. industrial gas furnace.
Q:Brief introduction to repair of industrial furnace
The industrial furnace is the main production equipment in the machinery industry. The repair of industrial furnace directly affects the quality, high yield, long life, low consumption and safe production of the furnace.
Q:Should the industrial furnace shell cool down?
The function of furnace shell is beautiful, protective lining, fixed function accessories and so on.
Q:What's the role of anchor bricks in industrial furnaces?
Anchorage brick is a new type of anchor brick relates to an industrial furnace, in particular to anchor brick of an industrial furnace roof, including column hanging end and the anchor structure, opened in the anchor on the surface of the spacing of the grooves in the anchor on at least one surface is arranged along the length direction ribs is provided with ribs, the ribs of the reinforcement and anchorage tension, tensile and flexural strength was obviously improved, the stress generated in the groove at the bar at the barrier can not continue to transfer, so the anchor brick of this kind of structure is not easy to break.
Q:Heat treatment equipment (industrial furnace), which products generally contain what kind of, which industries need to use heat treatment industrial furnace equipment.
The general metal die casting plant and the metal smelting plant need process melting and dissolving furnace, usually there are reverberatory furnace, cupola, rotary furnace, etc. I do the melting furnace of aluminium alloy.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range