BS5163 DCI non-resilient Gate Valve

Ref Price:
Loading Port:
China Main Port
Payment Terms:
TT OR LC
Min Order Qty:
-
Supply Capability:
-

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Specifications

1.General design:DIN,BS,ANSI
2.Rising or Non-rising stem
3.Solid wedge disc
4.Clockwise closing direction
5.Bolt bonnet

Product Name:

gate valve

Technical Data

DN40-DN2000mm

Body: Cast Iron, Ductile Iron

Stem: Stainless Steel,Brass

Disc: Ductile Iron

Flange Connection:EN1092-2 PN10/PN16/PN25,

                             ANSI B16.1

                             BS10 Table D/E,JIS10K/16K

Standard:DIN3352-F4/F5,BS5163,BS5150,BS3464,ANSI

Product Features

Bolt Bonnet

Replaceable O-ring

Low torque operation    

Outside screw and yoke

Clockwise closing direction

Graphite packing

Seat rings are pressed into wedge and body.

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:White steel faucet rust how to get rid of
Give you the same rust as it is recommended it. WD-40 (universal rust and rust cleaning lubricant) can penetrate into the metal surface and pores inside, but also for rust particles and other corrosion sediment has excellent solubility, can break the bond between the particles, so rust Such as precipitates easily fall off. And play a long-term anti-rust effect, known as "not rust rust agent." The WD-40 is highly permeable (stronger than water) and has excellent affinity for metal surfaces to penetrate into the metal pores to form a dense protective film of only 0.0028-0.0076 mm, effectively The moisture and moisture inside the pores have a strong permeability and metal surface affinity, can completely remove the grease attached to the metal surface, dirt, dust, etc. attached to the metal surface. Material
Q:Installing new faucet with sprayer into old basin?
You will need to drill another hole. The overflow you mentioned is called an Air-gap. It prevents the dishwasher drain from pulling a vacuum on the sink drain. They were required in some areas but now are being omitted from some codes.
Q:How do I stop my faucet from getting my counter wet?
You can replace the faucet with one that works better with your sink and doesn't cause the splash.
Q:Can the basin faucet hot and cold water pipe be replaced?
A small live wrench, a flashlight, drill into the basin below the table, the body off the table below the pot,
Q:how do i change the stem and seat in bathtub faucet?
once you close the provision of to the water heater that purely looks after the nice and comfortable water. in case you became you significant lower back on then curiously the leak is interior the chilly water furnish.
Q:Shower switch, hot and cold water pipe to reverse the impact of water?
Does not affect the water, check this faucet blister wire mesh is not blocked!
Q:Need to replace bathroom faucet?
You'll need to purchase a tap that matches the middle to middle size of your sink.I endorse Price Pfister, will rate just a little extra, however will final ceaselessly. Turn off the close off valves on scorching and bloodless. There's this distinctive wrench. Looks like a circular steel rod with a tee manage at one finish, and variety of a part moon with enamel at the different finish. Cost approximately $10. The toothed finish may also be swiveled for loosening(counterclockwise) or tightening. Use the device to loosen either side. And cast off the historic tap. If imperative, change the bendy hose or pipe that connects the tap to the copper pipe. Don't skimp in this, a couple of greenbacks extra will make the task alot less difficult. Fittings will need to fit on each ends of the bendy hose. Apply plumbers putty to the threads as you construct. Don't over tighten. When it is in combination, open the close off valves and verify for leaks.
Q:Cant remove a retainer nut from kitchen faucet?!?
spray WD40 on it this may take a couple of sprays but should do the trick i hope this helps you
Q:Master bedroom washbasin faucet how to install the washing machine tube
In the faucet below the water at the three links, and then split out a washing machine
Q:The nuts that hold my kitchen faucet in place are too tight but not rusty Need help unscrewing them. Advice?
The fasted way to remove to these nuts is to drill holes in the nut itself. You will need a variable speed drill and a drill bit which is larger than the nut itself. Drill 4 holes directly opposite each other where the nut meets the supply shank. Use a screwdriver and hammer and tap and twist the washer where the holes were drilled . The nut sections will seperarate and easily fall off. Be sure to wear safety glasses for eye protection while working overhead. Metal shavings are extremely sharp.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range