Brass Fitting For Multilayer Pipe

Ref Price:
Loading Port:
China Main Port
Payment Terms:
TT or LC
Min Order Qty:
1000 Pieces pc
Supply Capability:
10000 Pieces per Day pc/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

 

Brass Fitting For Multilayer Pipe 

1.PPR pipes&fittings;  

2.Brass fittings for composite pipes,water-heating pipes and brass pipes;

3.Water manifolds,etc.

 

Features of Brass Fitting: 

1.Material: Brass;

2.Applications: Brass fittings for composite pipe; 

3.Kind: Brassiness,nickel-plated,etc. 

 

Elbow (HF3025):

Elbow

Spec

16×10×1

 

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Hydraulic tubing connections are made of material steel
Such as carbon steel and cast iron, a much more used, less material costsBut if you're under a lot of pressure, try using carbon steel
Q:How to distinguish the type of tubing joint?
The oil pipe connection depends on what standard. It is convenient for you to contact me. Jensenshi@126.com. specializes in this thing.
Q:Connect with stainless steel tube with 304 stainless steel clip type pipe joint,
I personally think that the installation problem, that is, the card sleeve and steel pipe only after installation to reach the sealing effect, the installation quality can not meet the design pressure requirements.To avoid this situation, it is recommended that after installation 1.25 times higher than the design pressure test, test pressure can be put into use
Q:G1/8 "pipe joint end special sealing WD-B02 is what mean
The sealing effect is better than the traditional O ring. The elastomeric seals are used as axial static seals for threaded oil and screw ends, and the cross section remains almost constant at high pressure.
Q:What is pressing type pipe joint
A joint body core and buckling nut strictly, crimping connector still belongs to the soft seal
Q:What is the nominal diameter of the phi 1/2 in the pipe joint?
One foot (25.4mm) is divided into eight parts, 1/4, that is, 2/8 is two in charge, 1/8 is 1 in charge, 3/8 is 3 in charge, 1/2 is 4 in charge, in order to calculate nominal diameter
Q:The material is 304 stainless steel 1/4 "NPT" threaded joint. How much MPa pressure can be received?
The material is 304 stainless steel 1/4 "NPT" threaded joint. How much MPa pressure can be received?Answer: test pressure 2.5MPa; work pressure is less than or equal to 1.5MPa.
Q:What do you mean by "s" in the standard of pipe joint?
Did the landlord say "S" and "L"? S is a high voltage application, for example, at the P port. L is low voltage applications, generally used only in the oil return.
Q:How many bonding methods are there in the belt joint?
3. heat curing joint, the heat vulcanizing joint conveyor belt interface is completely closed, not susceptible to water wetting. Technology of belt vulcanizing joint is generally placed on the belt vulcanizer frame under the frame, both ends of the alignment, then put on the pressure plate, small thermal insulation board, insulation sheets, two vulcanizer installed on each side of 1-2 meters of the platform and fixed platform, the upper surface to the lower heating plate and flat surface homogeneous or slightly lower, also cannot affect the tension rod, the belt joint two on the platform began to cure. This method is a kind of joint is the best method that can guarantee the high coupling efficiency, but also very stable, joint life is long, easy to master, but the heat curing joint process is relatively complex, high requirements for personnel, cold bonding process is simple and short-term training posts.
Q:What are the sealing ways of pipe joints? Thank you
Pipe joint seal: thread seal, cone seal, end face seal.There are several kinds of thread seal:Hemp - thick lacquer, this is the most traditional.
Our productions have introduced the latest technology and advanced production equipment. With sound testing and inspection means and solid technical strength and scientific management, we are capable of producing high quality products and our production processes are in full accordance with ISO9001:2000 international quality management system standard. The characteristics of our product meet the national standards .

1. Manufacturer Overview

Location Zhejiang, China (Mainland)
Year Established 2006
Annual Output Value
Main Markets North America
South America
Southeast Asia
Africa
Oceania
Mid East
Eastern Asia
Western Europe
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage 91% - 100%
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size: 3,000-5,000 square meters
No. of Production Lines 8
Contract Manufacturing OEM Service Offered Buyer Label Offered
Product Price Range