Big Coil Galvanized Ironl Wire For Fencing

Ref Price:
Loading Port:
China Main Port
Payment Terms:
TT OR LC
Min Order Qty:
-
Supply Capability:
-

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Commercial Galvanised Steel Wire

(1) Quality : Meet GB/T 343 standard and other requirements of relevant standards .

(2) Zinc Coating: Meet GB/T 15393 standard and other requirements of relevant standards .

(3) Raw Material : Wire rod ——1006 , 1008 , 1018 , Q195 , etc, and zinc with 99.995% purity.

(4) Tensile Strength Range

Size (mm)

Tensile Strength (mpa)

0.15-1.60

290-550

0.65-1.60

400-550

1.61-6.00

400-1200

(5) Application : Used in wire mesh , artware , metal hose , binding for agriculture and construction , etc.

(6) Packing

Size (mm)

Coil Size

Spool Packing

Big Coil Packing

ID (mm)

OD (mm)

0.15-0.26

6 inch

1-14kg/spool

0.27-0.60

8 inch

1-100kg/spool

0.61-1.60

12/14/16 inch

1-100kg/spool

250-400

400-770

1.61-6.00

14-500kg/spool

450

800

508

840


(7) Zinc Coating

Meet GB/T 15393 standard.

Size (mm)

Weight of Zinc-Coating ( g/m2 )

A

AB

B

C

D

E

F

A1

B2

0.25

30

20

18

>0.25-0.40

30

25

20

>0.40-0.50

30

20

>0.50-0.60

35

20

>0.60-0.80

120

110

40

20

>0.80-1.00

150

130

45

25

>1.00-1.20

180

150

50

25

>1.20-1.40

200

160

50

25

>1.40-1.60

220

180

50

35

30

>1.60-1.80

220

180

70

40

30

>1.80-2.20

230

200

80

50

40

>2.20-2.50

240

210

80

55

40

>2.50-3.00

250

230

90

70

45

>3.00-4.00

270

250

100

85

60

30

>4.00-5.20

290

270

110

95

70

40

>5.20-6.00

290

270

245

110

100

80

50


Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Help with ceiling fan wiring?
The wires on the fan; the white wire is the neutral, The black wire and the black/white wires are the hot wires on the fan, one goes to the fan and the other goes to the light. The wires in the ceiling; The white wire is the neutral, it gets connected to the white wire on the fan. Check the black wire and the red wire to see if they are both hot. If not, and the black wire is hot and the red wire isn't. the red wire feeds another circuit somewhere. If the wire feeds another circuit, tie the red, black wires in the ceiling together with the black and black/white wires from the fan. Is there an outlet or light not working somewhere? If they are both hot, connect one to the black wire and the other to the black/white wire. Is there a wall switch involved here? If so, when the wall switch is turned on, does it liven either the red or black wire? If this is the case, the wire that comes from the switch should be connected to which ever wire on the fan is the hot lead for the light. The other wire in the ceiling would be connected to the hot wire for the fan. There's lots of different scenarios that are possible. If you aren't sure of what you are doing, GET SOME KNOWLEDABLE HELP TO CHECK OUT THE WIRING! No sense burning your house down to save a few bucks by not hiring a professional.
Q:50cc scooter wiring diagram?
I have a wiring diagram for my Vespa 50 but it is a 1967 with no battery, magneto only. What is the year of your scooter?
Q:Installing a fan ..... electric wires?
Of the two incoming wires, one should be white (neutral) and one should be black (hot or power). The bath fan should have a neutral and hot also. A wiring diagram can usually be found on the fan unit if a manual is not available. Simply wire the white/neutral to the neutral wire of the fan and do likewise for the hot wire. For safety modern fans make accommodations for the attachment of a ground wire. This provides a path to ground should there be a short in the unit. Hopefully there is a third wire from the wall that will provide a ground. It is usually bare and should be attached to the fan using a green ground screw. Older homes did not have the third ground wire but unless your home is from the fifties, you should have three wires. (If your electrical outlets accommodate three prong plugs, you have grounded wiring). If your bath fan is relatively inaccessible (on the ceiling) not having it grounded might not be that big of an issue but it is always better to ground the bath fan frame when possible. Again, if you have or can locate the manufacturers wiring diagram it should be followed.
Q:Where I can get paperclip wire.?
For the best answers, search on this site https://shorturl.im/axqI3 No, I am afraid you can't ... you need a special alloy, not paper clips, which are mild steel.
Q:Net force on perpendicular wires?
I didn't read the question so I was carefully working out the force. The wire is perpendicular to the first wire, so using the right hand rule you discover that the field it creates is PARALLEL to the first wire at this left end. The magnetic force is caused by the component which is PERPENDICULAR to the wire which is in fact zero. So there is no magnetic force at this point. As you move along the wire you get a diminishing amount of magnetism caused by the wire which is going out of the page but that field has a component which is DOWN the page. Therefore that part of the wire experiences a force which is into the page. ( take your right hand, put the thumb along the wire pointing to the right, the fingers point down the page, the palm points into the page which is then the direction of the force) I would be surprised if you were required to work out the magnitude of the force in this context. You can't use F= ILB because both the magnitude and the direction of the field varies at different points along the wire. If the perpendicular wire had been directly below the middle of the other wire there would have been no net force. If you were of a level where working out the force was appropriate you would need to set up the formula for B at various points along the wire, taking the vertical component only and integrate this over the range from 0 to 5 cm. Not a trivial mathematical task.
Q:How to replace electrical outlet 6 wires?
For the best answers, search on this site https://shorturl.im/awtUt Try this. take the plug out of the box, so that just the 7 wires are hanging there. Of course, your power is off before you do this. Take the 3 white wires and twist all their copper ends together. Then flip the breaker on. If the breaker does not trip, most likely those white wire are all neutral. If the breaker does trip, one of those white wires is being used as a hot (black) wire. If the breaker did not trip, turn the breaker off again. Now twist all 3 black wires together, flip the breaker on. If the breaker does not trip, the black wires all belong together. If the breaker does trip now, one or two of the black wires is being used as a neutral or is coming from a different source, such as another breaker or going through the outlet to somewhere else in the house. If the breakers don't trip either time, all black wires belong together and go on the brass screw of the outlet (or the side with the small opening). All the white wires go on the silver screw (or large opening of the plug). If it doesn't work, you will need an electrical tester to find out which wires are hot or wires that don't belong together because they may be a different voltage. Don't want to confuse you but there may be 220 volts in the plug between 2 of the black wires.
Q:wiring an electrical outlet?
Make sure you get an GFCI outlet ..
Q:2000 firebird wiring?
+1 for the LS1Tech site. I am a member and there is tons of info there and great people to help you out.
Q:Power control wire?
Control Wire
Q:wiring my amp up help?
The remote wire should be running from your amp, to your radio fuse. Just strip the wire and wrap it around the fuse and place it back in. That is the correct way to hook it up.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range