Q:Coke is how to produce, what is its purpose?

Under the condition of air isolation, the bituminous coal is heated to 950-1050 DEG C, which is finally made into coke by drying, pyrolysis, melting, bonding, solidification and shrinkage. Coke oven gas produced in the process of coking and recovery is not only a high calorific value of fuel, but also an important industrial raw material for organic synthesis.

Q:What are the uses of these early industrial iron and steel? Any difference?What kind of carbon do we eat in the middle of a long strip of carbon?

Charcoal:1 metallurgical industryIn the past, the charcoal was used to smelt iron ore, and the pig iron was melted by charcoal and coke. The structure and mechanical properties were not the same even if the chemical composition was the same. The charcoal smelting pig iron generally has the fine grain structure, the casting is compact, does not have the crack the characteristic, the pig iron with the charcoal production contains the impurity is few, is suitable for the production high quality steel. Due to the reduction of charcoal, so in the metallurgical industry can be used to restore ore smelting metal.In the non-ferrous metal production, charcoal used for surface flux, non-ferrous metal melting, the surface flux in the molten metal surface protective layer, so that the separation of metals and gases, can reduce the loss of molten metal splash, and can reduce the melting material in gas saturation.A large amount of charcoal is also used to produce crystalline silicon, silicon used charcoal ash production should not contain too much carbon and head.

Q:What is the difference between coke and carbon residue? Coke is a high-temperature refining, carbon residue can be used for civilian fuel it?

Gasification coke, which is used in the production of coal gas, is mainly used in the fixed bed gas producer with solid slag, as the raw material for gasification, producing CO and H2 as the combustible component:C+O2 - CO2+408177KJCO2+C - 2CO-162142KJC+H2O - CO+H2-118628KJC+2H2O - CO2+2H2-75115KJ

Q:What is the concept, relationship and difference between coke and coke? The main difference and contact, thank you

Formed coke is a product obtained through several steps:(1) environmental protection continuous high efficiency carbonization furnace(2) the use of anthracite powder to produce plastic molding coke and supporting technology(3) a new type of environmentally friendly carbonization carbonization furnace without three wastes discharge.(4) hydraulic press

Q:Distinction and distinction of cokeSoil coke, improved coke, coke machine coke do, what is the difference between

Two, the type of coke:Coke is usually divided by use of metallurgical coke (including blast furnace coke, coke and iron alloy coke, calcium carbide and coke gasification etc.) with coke. The pressurized pulverized coal forming coal, coke carbonization etc. in the new postprocessing process called Formcoke.1, metallurgical coke, metallurgical coke is coke, coke, iron alloy coke and non-ferrous metal smelting coke for metallurgical coke collectively. More than 90% are used in blast furnace, the furnace coke often called metallurgical coke.The metallurgical coke quality standard (GB/T1996-94) made in China is the quality standard of blast furnace

Q:Types of coke and use of coke

Generally speaking, the use of coke in the following industries: blast furnace ironmaking, mechanical casting, calcium carbide production, processing Ferroalloy, chemical fertilizer, gas and high-tech high value-added industries

Q:Standard grade two grade coke standard

5, the moisture in the coke: water fluctuations will make the measurement of coke is not allowed, resulting in fluctuations in furnace conditions. In addition, the increase in the moisture content of Coke will make the M04 high, M10 is low, the drum index error.6, the screening of coke composition: in the blast furnace coke particle size is also very important. In the past, the particle size of coke in our country is as follows: the coke size of large coke oven (1300 - 2000 square meters) is greater than 40 mm; the coke size of medium and small blast furnace is larger than 25 mm. However, some of the steel test shows that the coke particle size of 40 - 25 mm as well. Larger than 80 mm of coke to be whole, so that the particle size range. The coke block is uniform, the gap is large, the resistance is small, and the furnace condition runs well.

Q:What is the sample quantity of coke moisture test? What is the test time? How many degrees? That is the national standard.

Test procedureDetermination of total moistureA, said the samples size less than 13mm with pre dried and weighed for about 500g (referred to 1g), smooth specimen,B, a sample tray is placed on the 170 a 180 C in the drying box, LH removed after cooling, weighing 5min. C, check dryness, each time 10min, until the two consecutive quality difference in LG, calculate the quality of the last time.Determination of moisture content of samplesA, with the weighing bottle drying to constant quality in advance and has quickly called weighing samples size less than 0.2mm uniform mixing of the 1 + 0.05g (referred to 0.0002g), flat on the weighing bottle.B, will be filled with a sample of the bottle to be placed in the 105-110 drying box drying 1H, remove the weighing bottle immediately covered with lid, put into the dryer to cool to room temperature (about 20min), weighing.C, check of dry, insult 15min, until two consecutive poor quality in 0.001g, take the quality of the last calculation, if quality is weight gain first calculated on the basis of.Five, the calculation of test resultsCalculation of total moisture content according to formula (L):

Q:8 points will be isolated from the air to enhance the heat of coal, in addition to the main coke, but also the material listed in the following table: No.

The structure of benzene and toluene is similar, and the molecular composition is different from that of a CH2 atom cluster, which is called homologous;(5) the number of chloro compounds in the hydrogen molecule is equal to the number of hydrogen atoms in different environments, and toluene has four kinds of hydrogen atoms in different environments: methyl group on the top, the benzene ring on the top of the 3 species, and so on, there are 4 kinds of chlorine compounds in toluene,

Q:Why in the blast furnace ironmaking with coke instead of charcoal why coke can produce heat to improve the heat of the furnace how to produceWhy in the blast furnace ironmaking with coke instead of charcoal why coke can produce heat to improve the heat of the furnace how to produce

The role of coke in the blast furnace: 1 reducing agent 2 heating agent 3 skeleton role. Combined with the effect of coke in the blast furnace can know compared with coke instead of charcoal. The coke oven gas is produced high calorific value of fuel, and is an important raw material for organic synthesis industry.