BATHROOM SANITARY WARE TWO PIECE TOILET -8511

Ref Price:
Loading Port:
China main port
Payment Terms:
TT OR LC
Min Order Qty:
100 set
Supply Capability:
2000 set/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Specifications

washdown Two-piece Toilet
S-trap 200mm
Low in price,good in quality

Easy-clean glazed technology
10 years experience
Strict quality control

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Bathroom sink is loose?
Here's what you do: Under the sink at the again facet of the the drain you're going to uncover a lever rod that's connect with the manage you pull to near the pop-up. Where the lever meets the drain is a nut, which holds the lever into the pipe. Put a bucket or anything beneath the lure, keep the lever nonetheless and unscrew the nut. Now take hold of the pop up commute within the most sensible of the sink, raise it out even as doing away with the lever rod from beneath the sink. This will enable the commute to return out. Pull it out slowly, since the enormous lengthy slimy drain fish that is placing off of it's your situation. Clean that nasty mess off the commute, then reinsert it into the drain, even as utilising the lever to maintain it from falling the entire method down. Now your item is to get the lever finish into the gap on the very backside of the commute, then tighten the nut go into reverse, however no longer so tight that you just cannot with no trouble function the pop-up. After all that, which truthfully simplest takes approximately 5 mins, then you'll pour a few boiling water down the drain to eliminate any cleaning soap scum and hair gel that can nonetheless be within the drain. Here's to expertise, Noah
Q:Bathroom sink?
Again (I answered the front door question too) Home Depot/Lowes have TONS of sinks in stock to choose from, lots of round ones also. They come with the holes for the faucet but you have to buy the faucet seperately. They do come with everything else to install though.
Q:Help with replacing bathroom sink faucet!?
if your sink has shut off valves on it . you will be ok simply remove all the plumbing from shut off valve to sink . in replacement use specially designed sink supply tubes that are chrome and flexible it will be a snap and no plumber needed . not the solid looking chrome these are supply lines that are corrugated stainless wrapped around a pipe
Q:What is the height of the wash basin?
To confirm the location of the washbasin: in the floor tiles and wall tiles, it is necessary to confirm the installation of the wash basin position, because the installation of the bathroom cabinet is to be perforated in the wall, but also need water holes and drainage holes, once After the installation can not move the general position, so to confirm the location of the installation of a good bathroom cabinet is a prerequisite for pre-installation conditions.
Q:No hot water coming from the bathroom sink?
Tonya, It has nothing to do with the faucets. If you get hot water anywhere in your house, the water heater is not the problem either. When you turn on those faucets on as if to get hot water out of those faucets & the water NEVER gets hot, that means that your contractor improperly connected those faucets. In other words, those faucets are not connected to the hot water line. You're going to have to call that contractor back to have him fix his screw-up. Good luck.
Q:How much is the counter basin?
Hanging cabinet is usually more than 1.6 meters from the ground, too easy to meet, too high space becomes smaller, loaded items will be too small. The basin is typically 75 to 90 cm from the ground.
Q:best method for updating bathroom sinks?
Im not sure about updating it, but I guess you can remodel it, my parents put tile on there old one and it looks really good..
Q:What is the size of the bathroom counter basin cabinet?
Commonly used common basin size: 585 × 390mm, 600 × 460mm, 700 × 460mm, 750 × 460mm, 800 × 460mm, 900 × 460mm, 1000 × 460mm, 600 × 405 × 155mm, 410 × 310 × 140mm size specifications, In addition, there are many commonly used basin size, because the basin is a private bathroom sanitary ware, so in order to try to meet the needs of each user, manufacturers have to quit a lot of different sizes of the basin, and ultimately the current situation.
Q:how do i put a bathroom sink?
oh man....first of all, i don't know if you want to replace your sink or your fixtures or both? to remove the sink you will have to remove all the fixtures first. this can be simple to difficult depnding on tools you have, level of expertise, AND age and type of connections used. the sink itself is probably held in place by a series of small clamps connected to counter top and sink. as well as the drain pipes. unscrew clamps, disconnect drain, and it will pop right out. if you wanted to replace the old fixtures which is what i think you were saying, the best advice i can give you is to buy good grade new fixtures, then read and follow all directions. this would really be a wordy-confusing answer were i to try and describe what is actually a relatively easy fix. take your time, have patience, CUT THE WATER OFF, and you can do this thing. AND also while you are under there, go ahead and replace the old drain lines too; pee trap and all of that old plumbing. i would even put new shut offs in, but thats up to you. gl with it!
Q:Is it difficult to install a bathroom sink? If not what should I know?
Well the plumbing part is easy RE; Hot left the cold to the right, That means the hot is on the Left and the Cold is on the right, Watch how the old one comes out, most is a screw or bolts clamp to the counter and sometimes sealed with silicone which you can cut loose with a razor knife, Un hook the lines at the valve under the sink, if you don't have any then get some and put them in, On the new sink connect the faucet and the supply lines before putting in the sink, Set you sink in correctly and trim the supply lines even with the valve inner part so that it is all the way in and tighten the nut, after you turn the water back on, then slowly open the faucet and let the air come out, then run it for a while, some guy remove the faucet packing stem and then turn on the water, this flushes the line out and won't clog the faucet.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range