Ball and Socket

Ref Price:
Loading Port:
China Main Port
Payment Terms:
TT or LC
Min Order Qty:
1000 Sets set
Supply Capability:
10000 Sets per Month set/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

 

Ball and socket is a part of composite insulator.

 

we can make it according to customers' drawings and requirement. 

 

Brief

  • Ball & Socket type end fitting for composite Insulators application

  • Materials in C45, 35Mn2, 40Mn2, 45Mn2

  • Mechanical class 40kN - 210kN

  • Hot galvanized coating protection against corrosion

  • Magnetic article test on100% of components

 

Standards

  • Materials testing acc.to EN10083-1,-2, AISI-SAE J403

  • Dimension testing acc.to IEC 61466, ANSI C29.2

  • Galvanization testing acc.to IEC 60383, ISO 14713, 1461, ASTM A123, A153

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Joint type of pipe joint
NPT is the abbreviation of National (American) Pipe Thread, an American Standard 60 degree taper pipe thread, used in North America. National standards refer to GB/T12716-1991PT is the abbreviation of Thread Pipe, is a 55 degree taper pipe thread sealing, belonging to the Whitworth family, for the European and Commonwealth countries. Commonly used in water and gas pipe industry, taper regulations of 1:16. national standard is available on the GB/T7306-2000G is a 55 degree non thread sealing pipe thread, belonging to the family of Wyeth thread, marked G for cylinder threads. National standards refer to GB/T7307-2001In addition, the 1/4, 1/2 and 1/8 marks in the thread refer to the diameter of the thread size, in inchesYes, my wife usually refers to the size of the thread by one point, one inch equals 8, and 1/4 inches is 2, so by analogy
Q:For picture: hydraulic pipe joint M30*2H-G3/4
Specific prices must be based on drawings and materials.
Q:What are the installation requirements of the card sleeve joint?
(1) pre assembledThe pre assembly of the sleeve type pipe joint is the most important step, which directly affects the reliability of the seal. Special pre assemblies are usually required. The small diameter can be pre joint in a vise. The concrete method is to use a joint body as the mother's body and press the nut and the sleeve tightly onto the pipe. The utility model mainly comprises a sleeve type through pipe joint, a clamping sleeve type end through connection head, a clamping sleeve type three way pipe joint and other patterns. The author found that even if the same batch of goods of the same manufacturer, the tapered holes on these joints are often different in depth, resulting in leakage, and this problem is often overlooked.The correct approach should be to connect the end of the pipe with what kind of joint body, and the corresponding connection end with the same type of joint pre installed, so as to maximize leakage problems can be avoided.
Q:The pipe line of the hydraulic pressure pipe is formally installed
2.2. common thread is used for the connection and fastening between the mechanical parts, and the general thread connection is mainly made of coarse thread. The thread strength of the fine tooth thread is slightly higher than that of the same nominal diameter, and the self-locking performance is better.Mark 3. metric screw thread: M20-6H, M20 * 1.5LH-6g-40, where M represents a common thread metric, 20 nominal diameter thread is 20mm, 1.5 pitch, LH said, 6G 6H left, said thread precision grade, precision grade of internal thread uppercase, lowercase precision grade of said external thread, 40 screwing length;3.1. commonly used metric ordinary coarse thread pitch as shown in the following table (threaded hole diameter: carbon steel = nominal diameter P = nominal diameter cast iron; 1.05~1.1P; processing thread rod diameter = nominal diameter: 0.13P):Table 1 diameter / pitch of common metric coarse tooth threadThe nominal diameter of P cast iron bottom steel bottom thread rod diameter pitch P cast iron bottom bottom rod diameter of external thread steel
Q:New standard, how can the pipe joint be labeled, such as "3/4" taper pipe thread?
The English system is 55 degrees of thread, and the internal thread of taper pipe is Rc3/4. The outer thread is R3/4The U.S. is 60 degrees
Q:What does flaring pipe joint mean?
To match the cone of the joint, although the processing is troublesome, the sealing is reliable. In addition, the use of copper tubes in general, the expansion is relatively easy.
Q:How to choose the connection mode of clamp type flexible pipe joint correctly
The overall price of steel ring is lower than that of pipe endSummary: the middle and high pressure pipeline is recommended to use the pipe end connection, and the middle and low pressure pipeline is recommended to use the steel ring connectionThe customer can choose the clamp type flexible pipe joint (steel ring joint) or clamp flexible pipe joint (pipe end connection) according to the demand to reduce the purchasing cost.
Q:What are the names of all types of hydraulic pipe couplings?
The hydraulic connector is generally divided into: sleeve type pipe joint, flared type tube fittings, welded pipe joints, extruded hose connectors, quick connectors and rotary joints. Each class can be subdivided into several categories, such as pipe joint of sleeve type can be subdivided into sleeve type straight pipe joint, sleeve type bending joint, sleeve type pipe connector, three connector, four pipe sleeve type pipe joint, the next card set hinge joints, sleeve type pressure gauge connector etc.. Specific you can also go to Tianjin pairuite website to see very accurate classification is very small.
Q:Hot melt pipe joint leakage how to do?
2, dry leakage parts, with Wang Yu (waterproof cement) to buy. Less water, very thick situation, large surface paste in the water leakage position. This method is also used to remedy cast iron pipes.
Q:How to distinguish the type of tubing joint?
The oil pipe connection depends on what standard. It is convenient for you to contact me. Jensenshi@126.com. specializes in this thing.
We are a manufacturer and trading group specializes in the export of metal products. It mainly deals with various of ferrous metal & nonferrous metal castings and forgings, our main products covering water valves and fittings, power line fittings,fire-fighting equipments, motor & pump part, automotive & machine parts,.etc.

1. Manufacturer Overview

Location Dalian,China
Year Established 1994
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port dalian
Export Percentage
No.of Employees in Trade Department
Language Spoken: English,Chinese
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range