Axial Flow Pump From China Coal with High Quality
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 set
- Supply Capability:
- 1000 set/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Axial Flow Pump From China Coal with High Quality
1) Features: A) Vertical structure
B) Fitted with vertical motor
C) Long shaft
D) High efficiency
E) Good vapor erosion resistance
2) Applications:
A) Hydraulic projects
B) Farm-land irrigation
C) Industrial water transportation
D) Water supply and drainage
E) Water allocation engineering
3) Technical data:
A) Flow: 83 - 48, 888m3/h
B) Head: 1 - 30.6m
C) Medium temperature: 50oC
D) Operation pressure: 2.5Mpa
E) Diameter: 350 - 1, 800mm
F) Power: 4 - 20, 00kW
G) Voltage: 355kW, 6kV, 10kV
4)Material Standard：
A)Casing: cast iron
B)Impeller:cast iron/ Carbon steel/stainless steel
C)Shaft: Carbon/Cr-steel
5）Pictures
- Q:After reaching a height of 50 feet , there should be enough pressure to hose around 20 to 30 feet of water from it for curing concrete structure ex: columns, slab area etc. How many inches ( diameter ) of rubber hose is required to plug the water pump for pumping water ?
- 1 inch
- Q:Our CRN series pumps used in the 414V 480V 60Hz 60Hz power supply, what would be the effect? Is not the head can be reduced, there is no water pump and lift what voltage relationship?
- This is the world's Grundfos pump, if the pump itself support work under the 414V if it didn't need to worry about traffic and Yang Cheng, if the pump does not support the long time operation of the pump must lift and flow impact, and the multi-stage pump if it is Gao Yangcheng in the use of low lift it is also easy to burn the motor,
- Q:i have well water. suddenly i'm getting more pressure in my water. I have a well siofterner system. does anyone know what could be causing more pressure to come out from the water?/ thanks alot.
- The problem is either your pressure tank or your pressure switch. Since the switch is governed by the pressure in the tank, I would suspect the switch first - not the tank. You could check your pressure tank pressure using a tire gage, and make sure it is in the owner's manual operating range. The pressure switch tells the pump when to turn on and off - which is what fills the pressure tank. To check the switch, run the water until the switch closes and the pump turns on. Note the pressure at which it turns on. Now watch the pressure as it builds and note at what pressure it turns off. If you want less pressure, adjust the switch accordingly. We have ours set to come on at 42# and turn off at 65#. Our pressure tank air setting is 35 PSI.
- Q:I have a 1997 mercedes 320e and it is leaking very bad. I need a temporary fix for the water pump, so that I can take it to the repair shop that is 10 min. away.
- old mechanic trick get pepper and pour it in there/use a whole box if you have it/works
- Q:I took my car to a repair shop today, cause it was overheating,After looking at it for a few minutes the mechanic told me that it was a water pump problem.They quoted me a price of $276 to totally replace itI called around to my local auto zone stores and found out that the actuall pump cost for a new pump was $39 dollars, and I can get rebuilt pumps for 19 bucks, Is it that labor intensive that it would take so long to put in a 39 dollar part for over 200 bucks labor. Is that a fair deal, or am I getting ripped off.Additional Details, I didn't let them do the job yet, I took the vehicle home and just parked it in my driveway.
- Car Water Pump Repair
- Q:How can we calculate the maximum pump pressure for chilled water system for a 20 story building
- maximum stress tanks have a bladder interior them.The air is extra to the bladder to create a cushion of air, because of the fact the stress interior the tank builds up. Rule of thumb; while the pump is off and the stress interior the device is enable all the way down to 0, there ought to be 2# below shrink-in stress on your stress swap. i.e.- in the adventure that your stress swap is a 20/40, meaning it cuts in at 20# of stress and cuts out at 40# of stress, you may choose 18# on the bladder. in case you have an previous sort tank devoid of bladder, it ought to have an air quantity administration that provides air each time the pump comes on. Any air you upload to this sort of tank will ultimately get away so which you may choose to repair the situation with the air quantity administration. that's complicated and you may incredibly choose a provider individual to try this. e mail me and that i'll enable you recognize the thank you to do it if certainly you have an previous sort, bladderless, tank. desire to help!
- Q:We have a private well with a 40 year old water pump that is rusting away, and sounds like a truck. It's a double jet well pump sitting on a tank, with a second tank to one side that it's also connected to (with a thick pipe). I don't quite understand why there are two tanks (there's a third which is obviously the hot water). I'm guessing one of these is to hold water, and the other to provide air pressure? In any case, the pump runs OK, it doesn't leak, and provides plenty of pressure. It is just unbelievably loud. I've been told that replacing the bearings might take care of this problem, but seeing how the tank the pump rests upon (with a thin tube connecting it to the pump) is rotting away, and the system is older than I am, should I just replace the whole thing?
- I would replace the whole unit,for one if it was to go bad you are going to have water everywhere,and also the new one will be smaller and more energy effecient.
- Q:Had house power washed today and need my water to work again!
- What else got wet? Will it dry? If it doesn't, then shut the power at the panel and change the circuit breaker. Do not bypass the circuit breaker.
- Q:The dry season river dock company from the wharf area maximum height difference of 17 meters, is the need to purchase pumps for wharf surface wash pump water, the pipeline outlet pressure to the ordinary fire water pump pressure standard, the best do not directly into the water, can be placed in the dock or wharf surface from 10 meters (below three terminal position floor, 6 meters on average one floor), to facilitate the maintenance of. What type of water pump is the best choice? What brand is the best choice at home and abroad?! Be deeply grateful！
- Domestic I do not understand, only know that you dock water, it is best to use sea water pump, or allow manufacturers to do your anti-corrosionVille, Grundfos.Lift up, I'll do it. 30m is pretty muchThe self-priming pump is OKWhich brand do you want to use? Just call them directlyLet them count it for you and then type itFirst know about yourself, generally know a power head water quantity on the line
- Q:I have an 02 Gran Prix and my water pump is going out. With the recession I don't have the money to take it in. So can anyone give step by step instructions to help me fix it. I am a do it yourself kinda of guy so I am mechanically inclined. What tools will I'll need? is there a timing chain? How long will you think it will take me? Any thing i should pay attention to? How can I measure the pounds of torque that I put on the bolts or what tool will I'll need? Please help!!!
- WP replacement mini-writeup 1. Empy Coolant from Radiator drain 2. Remove SC and Acc. belts 3. Remove the coolant resevoir tank 3. Remove the Idler pulley with a 15mm 4. Remove the 4 WP pulley bolts with a 8mm 5. Remove the 2 Power Steering Pump bolts with a 13mm(bolts are at 12:00 and 6:00 accessable through the PS pulley holes) 6. Push PS pump 1 inch to the side 7. Remove all 8 WP bolts with a 13mm and a 10mm(3 are 13mm/5 are 10mm) 8. Collect extra coolant until flow stops(a few cups) 9. Apply RTV to both sides of the gasket and WP bolts 10. WP bolts should be torqued to 11lbs+80*/Idler pulley bolt at 36lbs/WP pulley bolts at ~9lbs 11. Reinstall everything and fill the coolant back up 12.
1. Manufacturer Overview |
|
|---|---|
| Location | |
| Year Established | |
| Annual Output Value | |
| Main Markets | |
| Company Certifications | |
2. Manufacturer Certificates |
|
|---|---|
| a) Certification Name | |
| Range | |
| Reference | |
| Validity Period | |
3. Manufacturer Capability |
|
|---|---|
| a)Trade Capacity | |
| Nearest Port | |
| Export Percentage | |
| No.of Employees in Trade Department | |
| Language Spoken: | |
| b)Factory Information | |
| Factory Size: | |
| No. of Production Lines | |
| Contract Manufacturing | |
| Product Price Range | |
Send your message to us
Axial Flow Pump From China Coal with High Quality
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 set
- Supply Capability:
- 1000 set/month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Related keywords
