Australia Standard PVC 45 Deg Plain Bend F/F

Ref Price:
Loading Port:
China Main Port
Payment Terms:
TT or LC
Min Order Qty:
3000 Pieces pc
Supply Capability:
1000000 Pieces per Month pc/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

 

Australia Standard PVC 88 deg plain junction F/F 

Item No.:AN/S004-4

Material:PVC

Standard:AS/NZS1254

 

Australia Standard PVC 88 deg plain junction F/F

 

Size:90mm

 

g/pc:130g

 

pcs/ctn:90pcs

 

N.W.:11.7kg

 

G.W.:12.7kg

 

Box Size(cm):58*36.5*55cm

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:How do you disconnect the PVC pipe joint that has been glued?
A sticky PVC pipe joint is not normally open. Only cut off and re connect.Do you know?
Q:How about the water pipe fittings and millimeters?20mm is 425mm is 6Why
Because, in the past, the workers who used these units were ordinary workers, so that they were easy to operate, and finally became 4 points, 6 points, and so on. In other words, it was also the wisdom of labour
Q:How many types of hydraulic connections?
Mechanical design manual fourth volume hydraulic pipe joint that part has detailed introduction and each installation size, and comes with the picture Oh, a glance will understand, hope to adopt Oh!
Q:What's the hydraulic pipe joint material?
The hydraulic oil of steel pipe and steel joint is not corrosive, so the hydraulic system is widely used in carbon steel joint, drinking water or pure water pipeline connection should not use ordinary carbon steel, before tightening air rules with brass, because the compressed air will carry water, gathered in the tube, if carbon steel will corrode the pipeline. The advanced air tightening machines do not produce moisture, so the rule is meaningless
Q:Hydraulic tubing connections are made of material steel
Such as carbon steel and cast iron, a much more used, less material costsBut if you're under a lot of pressure, try using carbon steel
Q:Who knows what the clamp joint standard is?
American Standard should be and not the same as ISO, but the actual products are the same?But in factories in the United States, they are strictly standard
Q:The pipe joint model is 1/2 "-14 teeth / inch"
The pipe joint model is 1/2, -14 teeth / inch: This is the English 55 degree taper pipe thread, the specific parameters are: big diameter 20.955mm, pitch 1.814mm, other parameters can be listed under the table:
Q:How to distinguish the type of tubing joint?
Corresponding to the different pipe fittings, you should have a good look at the mechanical design manual
Q:PVC pipe joint leakage how to do?
Method for solving leakage of water pipe joint:The 1. pipe itself is broken and can only be replaced with a new one.2., the mouth of the water leakage can be removed, if there is no glue pad should be installed on the rubber pad, rubber pad aging, change a new, silk mouth painted white paint, and then wrapped on hemp silk after loading, with raw material belt winding is also the same.
Q:Hydraulic jointWho knows the hydraulic connection "3/8*25.4=9.525" refers to the connection?
The most important part of the pre assembly of sleeve type pipe joints directly affects the reliability of the seal. A dedicated preprocessor is usually required. The small diameter can be pre joint in a vise. The concrete method is to use a joint as the mother's body and press the nut and the sleeve onto the tube. The utility model mainly comprises a sleeve type through pipe joint, a clamping sleeve type end through connection head, a clamping sleeve type three way pipe joint and other patterns. I found that even if the same manufacturer of a batch of goods, the cone of these joints on the depth of the hole is often different, resulting in a leak, and this problem is often neglected. The correct approach is to connect the end of the pipe with what kind of joint, and the corresponding connection ends are prefabricated with the same type of joint, so that the leakage problem can be avoided to the maximum extent.
CCDI is a leading largest and professional manufacturer for ductile iron fittings for water pipelines in China, Products for overseas markets covered all over the world.

1. Manufacturer Overview

Location Liaoning, China
Year Established 1994
Annual Output Value Above US$ 20 Million
Main Markets Mid East, Africa, Europe
Company Certifications ISO 9001:2008;

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port Tianjin; Qingdao
Export Percentage 30%
No.of Employees in Trade Department 500 People
Language Spoken: English; Chinese; Spain; Alabic
b)Factory Information  
Factory Size: Above 5,000 square meters
No. of Production Lines 2
Contract Manufacturing OEM Service Offered; Design Service Offered
Product Price Range Average