Art no. HT-TS1014 Ceramic knife set with acrylic stand
- Loading Port:
- Guangzhou
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1000 PCS
- Supply Capability:
- 100000 PCS/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Set includes:
6-inch carving knife,1.8mm
4-inch paring knife,1.6mm
acrylic stand
Blade:zirconia
Handle:ABS+TPR
Packing:with color box
You can choose the handle color you like
Zirconium material keeping 90° hardness just second to diamond which give the ceramic knife its outstanding sharpness and edge retention
Ergonomically shaped ABS + TPR handle in any color which keep the ceramic knife lightweight and colorful
Features:
Matte finished blade made of zirconium oxide (also calledzirconium)
Zirconium material keeping 90 degrees hardness just second todiamond which give the ceramic knife its outstanding sharpness andedge retention
Customized company names or logo on blades and packing ways arewelcomed
Advantages:
Transfers no metallic taste or smell to food
Has no acid and alkaline reaction with food
Lifespan is 10 times longer than conventional steel knife
Easy to clean up to prevent bacteria growth
- Q:Cubic boron nitride cutting tools for processing what materials
- Cubic boron nitride, commonly known as CBN, is a tool hardness second only to diamond material.It has high hardness, good red hardness, and almost all of the metal poor compatibility, but at the same time, poor toughness, non impact, easy to collapse.According to the above characteristics, cubic boron nitride, suitable for quenching materials (high hardness), high silicon steel, non-ferrous metal finishing and semi finishing.In particular, because of the incompatibility between CBN and C in cast iron, CBN is widely used in high speed finishing of iron castings.
- Q:What is the classification of the hardness level?
- 1,The hardness of carbon tool steel is about HRC62;2, the hardness of diamond in HV10000;3, the hardness of silicon carbide in HV4500.
- Q:How to select the tool according to the material
- The principle of NC machining tool selection is as follows:NC machining tool materials must be selected according to the workpiece and processing properties. Tool material selection should be reasonable, and the processing object, cutting tool materials and processing objects, mainly refers to the two mechanical properties, physical properties and chemical properties, in order to obtain the cutting productivity tool life the longest and largest.
- Q:How to calculate the machining time
- Machining distance mm divided by feed speed mm/min multiplied by 60S is the processing time
- Q:Why can't we use diamond tools to process iron materials?
- When the temperature is over 800 DEG C, the diamond will lose its cutting ability, and it has strong chemical affinity with the iron. At high temperature, the carbon in the diamond will soon spread to the iron, so that the edge of the crack". Therefore, diamond tools are not suitable for the processing of ferrous metals. Because of its high brittleness and poor impact resistance, it is very sensitive to vibration
- Q:How to distinguish between YG tool and YT tool and YW tool appearance
- From the outside can not see, buy or buy the finished welding cutter knife, there are markers such as YG8, YG6, YG3; and YT15, YT5, YT30 and YW1, YW2, hard alloy types and purposes are different; tungsten cobalt titanium, codenamed YT, the main component is WC+TiC+Co. Tungsten drill, code named YG, the main component is WC+Co. Tungsten titanium tantalum cobalt alloy general, known as YW, is mainly composed of WC+TiC+TaC (NbC) +Co tool, tungsten cobalt titanium type, suitable for processing of carbon steel and alloy steel, steel forgings; machining tool of tungsten cobalt for nonferrous metal and alloy, cast iron, heat-resistant alloy; tungsten titanium tantalum processing tool cobalt is suitable for heat resistant steel, high manganese steel, stainless steel, high alloy steel.
- Q:How to correctly install the tool in the machining center
- 1, the tool is long enough to expose the case as short as possible, as long as the clamping part. In addition, there is no damage to the barrel clamp.2, the main shaft of the tool is automatic tool change. Tool is installed on the knife according to requirements.3, the maximum weight of the tool, the maximum length, the maximum diameter requirements. Then is to control the tool's circular beat, the circular beat bad influence the machining accuracy but also damage the spindle.4, installation tool is not loose, confirm the tool in the handle is solid, the handle should pay attention to the rust, rust handle influences the machining accuracy of spindle hole wall damage.
- Q:PM rough machining, how to make the tool from the rough external introduction?
- I still do not understand, I did not set the rough boundary, but the knife or go straight down. Why do I set down the road very oblique knife out of depressed, today the initial processing broken two knives
- Q:Turning steel pipe, what is good?
- Feed from you for the 0.307 to judge, should not be a tool, but feed selection is too large, normally used coarse feed 0.3 is not small, not to mention the eccentric shaft, suggestions will feed appropriate small try.45# steel is generally used in the case of the YT15 is more suitable, YT5 poor wear resistance, YS8 brittle easy to jump knife. As for the speed depends mainly on the size of the workpiece diameter, if you use the cutting speed to measure, then the general rough car with 60 to 80 meters per minute, fine car with a 80 to 120 meters, the eccentric shaft should be appropriate to reduce the cutting speed.
- Q:What is the role of shield machine tools
- Fishtail knifeThe whole section cutter cutting soil, arranged in a different position on the cutting knife, knife disc from Zhouzhi center, full moon movement decreases, center theory can be regarded as zero. In other words, the length of the cutting soil in the sealed cabin is gradually reduced from the outside to the inside.
1. Manufacturer Overview |
|
---|---|
Location | |
Year Established | |
Annual Output Value | |
Main Markets | |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | |
No.of Employees in Trade Department | |
Language Spoken: | |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
Art no. HT-TS1014 Ceramic knife set with acrylic stand
- Loading Port:
- Guangzhou
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1000 PCS
- Supply Capability:
- 100000 PCS/month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Related keywords