Art no. HT-TS1012 Ceramic knife set with acrylic stand

Ref Price:
Loading Port:
Payment Terms:
Min Order Qty:
500 PCS
Supply Capability:
100000 PCS/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Set includes:

              6-inch carving knife,1.8mm

              4-inch paring knife,1.6mm

              acrylic stand



Packing:with color box

You can choose the handle color you like

Zirconium material keeping 90° hardness just second to diamond which give the ceramic knife its outstanding sharpness and edge retention

Ergonomically shaped ABS + TPR handle in any color  which keep the ceramic knife lightweight and colorful


Only use plastic or wood cutting board

As with only knife, avoid dropping, throwing or generalmisuse

Avoid using the ceramic knife to cut seeds, bones, frozen foodor other hard product

Not flexible, don't use it to smash garlic, open cans orattempt to bent it in any way

Hand wash only

Do not attempt to sharpen the ceramic knife yourself unless youhave access to sharpener specific to ceramic knives

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:How long is the control tool?
Do you want to carry a knife with you? The specification of the cutting tool is very long, I will give you the following: with self-locking device, without self-locking device is less than 60 degrees angle. As long as the above 2 belong to the control tool, if you bring a small dagger is only 6 cm long, but with a self-locking device, also belong to the control tool
Q:What is sintering and electroplating tools ah
Sintering definition:Macro definition: at high temperature (not higher than the melting point), other key green ceramic particles, grain growth, voids (pores) and grain boundary gradually reduced by the material transfer, the total volume shrinkage, density increases, and finally become a dense microstructure of polycrystalline sintered body, this phenomenon is called sintering.Microscopic definition: solid molecular (or atomic) are attracted to each other, by heating the particles to obtain enough energy for migration, make the powder particles bond, produce strength and lead to the densification and recrystallization process called sintering.
Q:Why can't we use diamond tools to process iron materials?
If you have to use diamond tools to process the iron material, you need to do a good job cooling, increasing the chip space, reducing the cutting force and other points, it is possible to process iron materials
Q:How to select NC milling cutter
In the free surface (die) processing, because the end of the cutting speed of ball end cutters is zero, so as to ensure the machining accuracy, cutting the apex densely spaced generally distance, therefore ball commonly used in curved surface machining. The flat tool has better surface quality and cutting efficiency of ball cutter, therefore, as long as the guarantee but cut under the premise of both surface rough machining precision machining, should be preferred flat knife. In addition, the tool life and the relationship between the price of great accuracy and tool, must pay attention to is, in most cases, choose a good tool while increasing the tool cost, but the processing quality and efficiency of the improved, can make the whole process cost is reduced greatly.
Q:Cutting tool materials
Commonly used tool materials are divided into: tool steel (including carbon tool steel, alloy tool steel, high-speed steel), hard alloy, superhard cutting tool materials (including ceramics, diamond and cubic boron nitride, etc.)
Q:What is the difference between insert and cutter
A big difference, the former is welded on the operation, trouble, after welding, grinding to open front, trouble, but the economic, however, if there is no special grinding tools like disposable almost, the latter is directly replaced by screws can, convenient blade welding blade than your price many, usually in 20 to 40 yuan a
Q:What is the classification of the hardness level?
1, the hardness of cemented carbide tools generally between HRA89.5~92.8;2, the hardness of high speed steel is generally between HRC62~65;3, super hard high speed steel hardness between HRC69~70;
Q:What are the causes of tool wear in cutting?
Phase change wear. Because of the increase of cutting temperature, the metallographic structure will change, and the hardness of the cutting tool will decrease, which will lead to wear.
Q:Tool quenching method
If you want to get a good tool, you should choose a good material, get the normal heat treatment plant to heat treatment.The purpose of heat treatment is by changing the internal structure of materials (such as tool steel: pearlite and cementite (or) (by heating and fast cooling) and martensite (low temperature tempering), tempered martensite), achieve the desired performance.In general, the performance of the alloy tool steel after heat treatment is better than that of carbon tool steel after heat treatment. Alloy tool steel, the number of alloy elements, different varieties, heat treatment performance is also different.
Q:What do PCD cutters and PCBN cutters mean?
CBN has high hardness, chemical inertness and thermal stability at high temperature, so it is widely used in grinding process as abrasive CBN grinding wheel. Due to the characteristics of CBN is superior to other tool materials, so people began to be applied to machining, but the small particles of CBN single crystal, it is difficult to make the tool, and the sintering of CBN is very poor, it is hard to be made of CBN sintered body, the larger until 1970s, the Soviet Union, China, countries such as Britain and the United States it have been successfully developed as CBN sintered, polycrystalline cubic boron nitride cutting tool PCBN (Polycrystalline Cubic Boron Nitride). Since then, PCBN with its superior cutting performance in various areas of cutting applications, especially in the high hardness materials, difficult machining materials in the cutting process is unique. After more than 30 years of development and application, there have been used to process different materials PCBN cutter material.

1. Manufacturer Overview

Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range