|Safe working load||kg||340||230|
|Maximum working height||m||36||38|
|Maximum platform height||m||34||36|
|Maximum horizontal outreach||m||22.1||24.2|
|Turntable tail swing||axle furled||1.68|
|Vertical distance below the horizontal extension level||m||1.98||3.27|
|Overall width||axle furled||2.49|
|Working platform size||m||2.4×0.9|
|Minimum ground clearance||m||0.32|
|Minimum turning radius||axle furled||4.5/6.85|
|Turntable rotation angle||ì||360∑（noncontinuous rotary）|
|Platform swing angle||ì||160∑|
|Fore arm amplitude angle||ì||130∑(+70∑/-60∑)|
|Running speed (furling state)||furled||km/h||4.8|
|lift or extend under 24||km/h||1.1|
|lift or extend above 24||km/h||0.5|
|Maximum allowable angle during working||ì||5∑|
|Hydraulic oil tank||L||208|
|Tyre (solid tyre)||445/65 D22.5|
-Can bus line intelligent controller
-Platform weighing limit function (EN280 standard)
-Turntable 360° continuous rotary
-Automatically adjustable platform
-Electric circuit fault code display
-Hydraulic swing platform
-Restart the engine protection
-Driving motor overtemperature protection
-Euro Ⅲ emission standard engine
-Hydraulic electric welding machine
-Hydraulic air compressor
-Hydraulic high pressure water pump
-AC power source connected to platform
-Platform working lamp
- Q:Hydraulic platform repair work instruction book, trouble which big man helps to provide
- The maintenance system of elevators is maintained every month. Roller, intermediate shaft and bearing, oil cylinder pin shaft and bearing, arm hinge shaft and bearing, etc. All parts are filled with lubricating oil to extend the life of the bearing.
- Q:How to automatically lift up and lift
- If I want to reach a certain time, the platform automatically drops, how to achieve? There is a time relay. Thank you very much!
- Q:Can the stepping motor drive the hydraulic platform?
- The hydraulic platform is driven by an oil cylinder, and the motor drive is a completely different way through mechanical means (screw, chain, gear, rack, etc.). In addition to mechanical means, depending on the power size, the step motor usually means that the equivalent power is not much, the maximum is a few hundred watts. The hydraulic platform is generally heavy, so it's unlikely. Or do you use a step motor to drive the hydraulic pump? It can, but also to consider the power problem, said earlier, smaller power stepping motor, if the original motor is a few kilowatts, certainly not.
- Q:The characteristics of hydraulic platform
- Light weight, good maneuverability, suitable for individual operation. The special mast strap-step device, which is smoothly and smoothly; 3, compact structure, small size of transportation, can enter the car of general elevator and pass through the door and narrow passageway. Double protected leg structure, work safer, and can be close to the working face lift.
- Q:Diablo ii flame volcanic mission will not be able to jump
- Push the pole to the right to climb quickly to seize the board on the wall, press the left key to left, after the magma press e and ran to the front of the counter, jumped to the table according to move to the left along the plate on the plate
- Q:The home is decorated, make a tatami mat the platform should pay attention to what aspect?
- The first is the choice of control. Usually tatami lifting column control mode are: pure manual type, electric type, manual and electric integration and so on three kinds of control modes, the future there will be mobile intelligent control. The pure manual type, which is to turn the crank, makes the lifting platform up and down. The advantage of this type of control is that even a blackout does not affect the use of the product. The disadvantage is that manual control is time-consuming and time-consuming.
- Q:How to use the ball screw platform?
- The search is also practical for the platform overhaul. Hope is useful to you.I hope my answer will help you.
- Q:Put the large beaker of water on the horizontal platform
- The inside of the large beaker is raised, the pressure on the surface of the large beaker is larger, and C is right. The pressure of the bracket on the glass is downward, the pressure of the gas is rising, the glass gravity is constant, the pressure of the bracket is greater for the glass, and the D is wrong
- Q:How does hydraulic platform change sealing ring, how to operate
- Because the concrete structure of hydraulic cylinder is different, the order of disassembly is different, and it should be judged according to the specific situation.
- Q:How do I design this hydraulic lift?
- I have to write a hydraulic part that is 40 or 50 pages, you can find the estimate here is a little difficult, still go to the library search.
1. Manufacturer Overview
|Annual Output Value
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
|No.of Employees in Trade Department
|No. of Production Lines
|Product Price Range