Applied fields of Rolling Forged Steel Grinding Ball with Supper Hardness apply for all kinds of Mineral Processing

Ref Price:
Loading Port:
China Main Port
Payment Terms:
TT or LC
Min Order Qty:
25M.T. m.t.
Supply Capability:
200000M.T./Year m.t./month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

1. Applied Field of Forged Steel mineral ues Grinding Ball with High Hardness and Low Breakage Rate
1) Power Plant, 2) Mineral Processing,

3) Refractory Factory, 4) Cement Plant

Applied fields of Rolling Forged Steel Grinding Ball with Supper Hardness apply for all kinds of Mineral Processing

2. Specification of Forged Steel mineral ues Grinding Ball with High Hardness and Low Breakage Rate
Metrial: Mn65,Mn50,Mn60, High and low chrome cast steel

Size: 20mm-150mm
Hardness:HRC58-65; Chrome content:11-14%

3. Packing Information of Forged Steel mineral ues Grinding Ball with High Hardness and Low Breakage Rate
Container Bags: 1000Kgs/Container Bag
Steel Drums: 850Kgs/Drum

4.  Photos of Forged Steel mineral ues Grinding Ball with High Hardness and Low Breakage Rate

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Is 316 casting better than 304 casting?
The degree of difficulty in the process of casting depends mainly on the structure, precision requirements, and hardness of the casting.
Q:What are the factors affecting the machining process of the casting material and structure?
The impact on the machining is obvious, it should be the material and heat treatment of the castingCarbon steel parts should be treated by heat treatment (annealing) without special conditions. It can effectively prevent the uneven hardness and hard points. It is easy to turn.
Q:The difference between cement sand castings, resin sand castings and vacuum casting parts
Our country or international, in all casting production in 60 ~ 70% by sand casting is produced, of which about 70% is used in the production of clay sand. The main reason is that the cost of sand casting is low compared with other casting method, simple production process and short production cycle. So as the car engine cylinder body the cylinder head, crankshaft castings are produced using clay wet sand molding process. When the wet type can not meet the requirement to consider the use of clay sand table dry sand, dry sand mold or other sand.
Q:What is the difference between forging parts and casting parts?
The casting parts are low in cost and short in production period. Because the molten iron has good flow properties, complex shapes can be formed. But because there may be sand holes, pores, shrinkage holes and other defects, the quality is unstable, easy to produce many defects, mechanical properties are not forged well, thus affecting the service life.
Q:How do casting parts remove stress?
Annealing treatment, according to different casting annealing treatment, eliminate thermal stress, if need to restore hardness or increase hardness, and then quenching treatment
Q:Where is the difference in performance between the rolled and cast parts of the same part?
The performance is too extensive, I think the following several people all fall into the erroneous zone directly, the performance includes a series of aspects:Mechanical properties: tensile strength, yield strength, elongation and contraction ratio of section and impact toughness after etc.
Q:How to improve the surface roughness of casting parts?
First, the accuracy of the model should be improved; two is to change the molding technique; the three is the coating; and the worker's technical level.
Q:How can the casting be quenched and tempered?
Return, general castings (especially steel castings) commonly used heat treatment process is normalized and tempered. Of course there are completely by annealing or remove stress annealing...
Q:Cast iron, casting parts 5
1, qualified enterprises will directly iron ore into molten iron, and then poured into the mold, such a good product performance. I work in the cast iron industry, which I can tell you for sure.2, this, like the Great Wall Motor Company has its own parts production department, as well as the corresponding mold center, so it will be their own casting. If the manufacturer does not have these departments, they can only place orders for others to do.
Q:How to get rid of casting sand inside casting parts?
Are you saying that in the sand casting cavity? We use the manual blast, he is like a pipe will be automatic shot out of the grit, into the casting cavity, to remove the internal cavity in the purpose of casting sand!
CDE is one of the largest factory specialized in producing Forged Grinding Balls and Cast Grinding Balls in China. Our annual production of grinding balls is about 100,000 ton. Our company has passed ISO9001: 2000 quality system authentication. We mainly export our grinding balls to Chile, Peru, Ghana, Argentina, Philippine, South-Africa, Italy, Japan, Korea, India, Australia etc more than 20 countries and areas.

1. Manufacturer Overview

Location Shandong, China
Year Established 1971
Annual Output Value US$50 Million - US$100 Million
Main Markets Domestic Market, Southeast Asia, South Asia, North America, South America
Company Certifications ISO9001;IS014001 Certificate

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port Qingdao Port
Export Percentage
No.of Employees in Trade Department 6-10 People
Language Spoken: English, Chinese, Korean
b)Factory Information  
Factory Size: Above 60,000 square meters
No. of Production Lines Above 10
Contract Manufacturing Forged Grinding Ball,Cast Grinding Ball,Casting Cylpebs,Grinding Rods,Decorative Steel Ball
Product Price Range Average