Packaging & Delivery of API High Pressure /Stainless Steel /Gas Needle Valve
Packaging Details: wooden cases,plywood cases,or according to customers' request
Delivery Detail: 40 days or according to customer's request
Specifications of API High Pressure /Stainless Steel /Gas Needle Valve
2)Connection:screw joint,internal thread
4)Operating Type:T-lever, handweel
Applicable Medium: Oil. Water. Gas and other corrosive or noncorosive medium
The Materials for Manufacture:304SS,316SS.316L,brass
The Demands for Fitting Pipes:Φ3 to Φ30
Cone Thread: ZG, R, GPT, NPT.etc
- Q:Why can hot runner needle valve be blocked?
- May be a small needle valve, or is not standard and not with the nozzle aperture valve needle understanding.
- Q:How can I see a needle valve in plastic products?
- Do good needle type mold, the glue inlet port is generally lower than the product surface, in front with no obvious signs of the case can be used to identify the surface color, into the plastic needle valve mouth is used with cooling gel, ambient temperature will be higher than the nearby, slightly shiny.The needle tip of the valve will also have obvious marks, because the high temperature and the entrance of the glue hole will always be more or less bright or rough than that of the die steel.
- Q:The hero can help solve the valve pin, hot runner, into the gate, white spots problem?
- Field analysis is required!It's OK to use our hot runner
- Q:If the material selection is not appropriate, long time production, will cause wear of the valve needle, some suppliers use inferior needle valve, or valve needle without cutting, non professional technology, can easily lead to the valve needle top is not smooth, resulting in gate galling phenomenon, the effect is not good, the final effect the quality of products. I hope I can help you
- That's what it says. It depends on the material you formed, but I think it's safer in the 0.3 wire.
- Q:Napping needle valve type hot runner gate part of what is the reason? Do you have any expert answers?
- If the material selection is not appropriate, long time production, will cause wear of the valve needle, some suppliers use inferior needle valve, or valve needle without cutting, non professional technology, can easily lead to the valve needle top is not smooth, resulting in gate galling phenomenon, the effect is not good, the final effect the quality of products. I hope I can help you
- Q:How to use the needle type oil cup
- Method of use: D needle type oil cup is a cup, the cup is a middle upper lid, from the top to the bottom through a needle valve, the cup cover is bending spring, pressure spring pressure to the middle of the adjusting nut adjusting nut to adjust the valve pin to the top of the lower end of the oil outlet open the upper part, and sideways to erect it can put the valve open to the maximum.
- Q:Working principle of needle valve type oiling cup
- The upper part and sideways to erect it can put the valve open to the maximum.The working principle is very simple, there are like you a look to understand, D is part of a cup, the cup is the top cover, the middle from the top to the bottom through a needle valve, the cup cover is bending spring, pressure spring pressure to the middle of the adjusting nut to adjust the adjusting nut to the top of the needle valve at the lower end of the oil outlet is opened, and the upper part of the right to erect it can put the valve open to the maximum.
- Q:Does the needle valve hot runner have adhesive problems? What are the possible causes?
- ExistingWe asked coreter hotrunner maintenance customer servicePossible reason: the valve needle does not emit too much heat.Handling: reduce hot nozzles and gatesThe temperature increases with cooling time.
- Q:Injection mould hot runner system needle taking needle tool
- The needle system of each hot runner company are different, the heating needs of general, pull out, because the structure is not the same, the use of tools are not the same, some companies do their own fixtures. Is the best request to the hot runner company. Let the staff training
- Q:How long is the needle length of the needle valve?
- This depends on the size of your mold, the thickness of the cylinder height, the thickness of the flow plate, and the length of the hot mouth, as well as the needle valve to reach the location of the product and so on, to be integrated calculation. There is no fixed size
Product range: (1)Valves:gate valve,check valve,globe valve,ball valve,butterfly valve,control valve,safety valve,angle valve,Titanium alloy valve, thermostatic valve,needle valve,plug valve,etc. (2)Flanges and Pipe fittings:all kinds of flanges,elbow,tee,caps,union,plug,coupling,reducer,etc. (3)Pumps:Sewage pump,sand suction pump,centrifugal pump, mixed flow pump,hand press pump,self- priming pump,etc.(4)Faucet:ABS shower head,LED shower faucet,kitchen faucet,basin faucet,etc. (5)Small brass valve:ball valve,angle valve,etc.
1. Manufacturer Overview
|Annual Output Value
||20.00% Mid East
10.00% North America
9.00% Eastern Asia
8.00% Northern Europe
7.00% Domestic Market
7.00% Western Europe
6.00% South Asia
6.00% Eastern Europe
5.00% Southern Europe
4.00% South America
3.00% Central America
1.00% Southeast Asia
||ISO 9001:2000;CE;API;ENVIRONMENTAL MANAGEMENT SYSTEMS CERTIFICATION CERTIFICATE
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
||71% - 80%
|No.of Employees in Trade Department
||English, Chinese, Japanese
|No. of Production Lines
|Product Price Range