1 Used for 19"cabinet ,Complete metalation and reed construction, modularization design
2 IDC: phosphor bronze and silver plating (20-50uinch), suitable diameter 0.4-0.6mm, durability 200 cycles
3 Contact pin: phosphor bronze and gold plating (20-50uinch), mating durability not less than 750 cycles
4 Anti-burn performance: plastic part made from PPO and PC, meeting the international standard
5 Intermediate resistance: no more than 2.5m ohm in normal atmosphere pressure (not including bulk resistor)
6 Insulated resistance: no less than 1,000M ohm in normal atmosphere pressure
7 The intensity of anti-currency: DC 1,000V (AC,700V),No puncture and flash-over phenomenon in one minute. Accord with industry standard
8 Label: clear label to ensure easy to manage
9 Type: 50,Voice patch panel.
Meet TIA/EIA-568-A and TIA/EIA-568-B Category 3 requirements.
Meet TIA/EIA TSB-40
Meet ISO/IEC Generic Cabling Standard 11801
Meet CENELEC Generic Cabling Standard EN50173
Angle: 90 Degree
Termination: Krone Type
According to UL 1863
Current rating: 1.5 Amp Max.
Voltage rating: 150 Volts
Contact resistance: 20 m-ohm
Insulation Resistance: 500M-ohm
Dielectric Withstand Voltage: 1000 V AC RMS, 60Hz 1min
Housing: PC UL94V-0
IDC: PC UL94V-0, Accept 22-26 AWG Solid Wire.
PCB: FR4 1.6mm(0.04") thickness, 2 layers
Contact: PC Ul94V-0, 0.45mm(0.018") Diameter Phosphor bronze with 3 u" to 50 u" Gold plating on contact area.
- Q:Buried in the underground PVC threading pipe in the wire was blisters, about two days or so, with air compressor blowing out of the water, so that there is no problem after this circuit?
- You are completely correct, you can choose a variety of connection methods, graphics quality from good to bad followed by VGA (D-SUB), color (component), S terminal, video.
- Q:How is the tee of the threading tube on the drawing?
- The size of the current directly related to the power, but also with the voltage, the other, the power rate (also known as power factor) and so on Generally there are formulas available for calculation, because the factory is commonly used 380/220 volt three-phase four-wire system, therefore, according to the size of the power directly calculate the current
- Q:3 by 16 cable is a few flat? How? That 5 by 16?
- May be caused by the leakage of upstairs, may also be caused by moisture, check out the reasons to change.
- Q:To ask the gods, with cad cable tray design, how to take into account the layers? Is a layer of a painting or a few layers together, how to set the specific color
- Engage in what, put on the wallpaper does not become a dark line yet. Ming line is very practical. Or you shop in the ground or hidden in the base line it
- Q:Ask you master: cable puncture clip and T terminal What is the difference?
- This is not a problem with voltage instability. This is your power cord material does not work, your graphics card over current is very large, resulting in yellow line 12V over current, and the wire will lead to poor impedance will gradually become larger heat, over time will burn the power cord. It is recommended to replace a power cord with a good material.
- Q:How to identify the true and false of the wire (copper wire)
- The length of the kbg line is 1.0mm, the other is 1.2mm, the Φ. Φ. Φ. Φ.
- Q:Will the weak machine room use a hanging cabinet? (Own) to have a heat impact, if you want to use patch panels, put what position more appropriate! The The Ask the great god to help
- How many meters of cable can be customized according to the requirements.
- Q:The dog is very disobedient and how to do it
- Low voltage and wire aging has nothing to do with the cross-section of the wire, the cross-section is small, then the resistance of the wire is large, the pressure drop is large, the user's voltage will be reduced, but also with the wire and wire connection resistance, contact resistance Large, but also cause the user to drop the voltage, low voltage and the aging of the wire has an indirect relationship, the wire aging, that there is a certain history, and in recent years, rising living standards, household appliances also increased, with the time Increased, the power has increased, relative to the wire is concerned, is overwhelmed, so the line is often the place where the line voltage is very low
- Q:On the Grounding Problem of Cable Bridge in Factory Building
- and then audio cable and video cable [audio line (red and white), video cable (Yellow)】 corresponding to the color connection set-top box and TV If the set-top box and TV are high-definition, you can also use high-definition multimedia interface cable (HDMI cable) to connect the TV and high-definition set-top box HDMI interface Note: high-definition multimedia interface line the corresponding line connection is correct, you need to check the signal line and audio and video lines are loose; after installation, turn on the TV and set-top box power, then use the TV remote control signal source conversion To the corresponding set-top box input video signal source; until the automatic search after the program, you can watch the TV program
- Q:Outside the pipe network into the basement distribution line between the line (dozens of lines) how to prevent water
- Under normal circumstances, according to the "construction of electrical engineering construction and acceptance of GB-2002" requirements and design requirements, living room air conditioning (three-dimensional air conditioning) socket height 300mm away from the distance. And hang up the air conditioning socket height of 1800mm. Ordinary sockets and weak sockets are 300mm from the ground, and the pitch is 300mm. The kitchen and toilet socket is generally designed to distance 1500mm, Yuba socket for the 2100mm, range hood socket 1800mm. Switching height is generally 1300 ~ 1400mm. The above is the electrical aspects of the delivery of a scale. Late owners of the electrical aspects of renovation, to consider the laying of floor or floor tile thickness, to ensure that practical and aesthetic effects. PVC depends on whether you are loading the line or dark line
Our corporation's products cover more than ten categories and over 200 specifications, including Cat5e, Cat6 keystone jack series, patch panel series, face plate series, multimedia casing series, junction box series, distribution cabinet series, clamp module series, protection unit series, insertion tool series, STB series, PCB socket series, cross connection terminal and heat-shrinkable sleeve series, MDF, DDF and ODF series, fused fiber splice modules (trays), integrated fused terminal trays and other telecommunication accessories.
1. Manufacturer Overview
|Annual Output Value
||US$5 Million - US$10 Million
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
||31% - 40%
|No.of Employees in Trade Department
||Below 1,000 square meters
|No. of Production Lines
||OEM Service Offered Design Service Offered Buyer Label Offered
|Product Price Range
||High and/or Average