Aluminium Profile- AA6060

Ref Price:
Loading Port:
China Main Port
Payment Terms:
TT OR LC
Min Order Qty:
-
Supply Capability:
-

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Product Description:

1 Specifications of Aluminum Profiles 6061-T5

Alloy Number

6063  6061  6060 and different aluminium alloy

Temper

T4  T5  T6 or other special status

Surface available

Mill finish, Anodized, Powder Coating, Wooden transfering, electrophoresis, heat insulation, PVDF, and deep processing

Thickness:

>0.8mm

Width:

<300mm

Standard

GB5237.1-2008

Special Specification is available on customer’s requirement

2 Usage/Applications of Aluminum Profiles 6063-T5

Aluminium Profiles are widely used in construction(windows & doors,curtain wall), decoration ( flooring and tiling, kitchen) and industry ( heat sink ).

CNBM produces aluminum profiles which meets the national standard GB5237.1-2008. Our strong quality control term bring you the most-qualified products. And with state-of-the-art equipment, and the state owned company background, we have to say, you will understand why there are so many company choose CNBM to be their supplier.




Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:What brand of aluminium tube is in freezer?
The 7075 is Aluminum Alloy grades, belonging to the Aluminum Alloy 7 Series (1XXX is pure aluminum, Al Cu mg Al Cu Mn is 2XXX or 3XXX, 4XXX generally do manganese aluminum brazing sheet, 5XXX Al Mg, 6XXX Al Mg Si, Al Zn mg Cu 7XXX)7075 chemical compositionFerrosilicon, copper, manganese, magnesium, chromium, nickel, zinc, titanium, other (3) aluminum (4)Each total0.4, 0.5, 1.2-2.0, 0.30, 2.1-2.9, 0.18-0.35 - 5.1-6.1, 0.20 (5), 0.05, 0.15, remainder
Q:What happened to the mold sticking when drawing the aluminum pipe? How do you make the mold?
1. apply mold release agent 2. on the mold. The necessary taper shall be taken into account when the die is designedAskWhat angle is that design?Chasing the answerSmall angle, in order to facilitate the separation of the workpiece and the die. Theoretically, the greater the angle, the better the release, but without affecting the size of the workpiece as the premise, there is no fixed degree. Tests are necessary.
Q:How to trap 50 tube refrigerator
Cut off at the point of leakage, with a copper knot to connect the head, you should pay attention not to force too much.Now the refrigerator tube is the use of aluminum tube or Bondi tube (Bondi tube, that is galvanized steel pipe, in fact, iron pipe, iron pipe above the paint once lost, it is easy to rust. )The aluminum pipe is more corrosion resistant than the iron tube, and the iron pipe is not corrosion resistant. In fact, the best or copper pipe, but now no manufacturers have produced, mainly or cost.
Q:Freezer aluminium tube can be used for several years
Now the refrigerator tube is using aluminum tube or Bondi tube (Bondi tube, that is galvanized steel pipe, in fact, the iron pipe, iron pipe above the paint once lost, it is easy to rust..)
Q:How can the aluminum pipe burr be convenient?Burr left by drilling
The internal tube is burr! Not very long words can be a round drill clamp in the round head through a 1 mm wide and about 30 mm in the hole, and then put the paper cut up into 30 broad band card in the slot to rotate in the opposite direction wrapped up! Until Guan Zikong was slightly more than a little good! So you can clear burrs on the inner wall of the!
Q:How to repair the surface defects of aluminum pipe
Third, the pipe is used to do it, the thickness of a pipe length measurement and recording, in general use will be selected according to the use of its wall thickness specifications and the length of the specifications, if found to have stiff head tubes should be timely marked when used to head to stiff it uses the slow speed, and high temperature.Fourth, after the completion of the expansion pipe, aluminum pipe to the appearance check to see whether the pipe surface defects, if flawed, allowing him to eliminate the timely elimination of defects if too much, not to be able to restore to enter the furnace re grinding clean.When the fifth tubes are heated, the thickness of the top three branch material shall be measured. After the expansion is completed, a measurement shall be carried out, and the expansion speed and temperature shall be adjusted according to the changes of these two measurements.The whole round repair of aluminum tubes is the most common repair in the industry, with the following methods for repairing the pits or flattening
Q:What is the tensile strength of the 6063T5 aluminum tube and what is the elongation rate?
The tensile strength of 6063T4 aluminium tubes is about 150. The elongation rate is about 10%. T6's around 230. The elongation rate is about 8%As it were, you can Q me: 88099379 (Shanghai Xuan Sheng)
Q:What's the difference between extruded aluminum tubes and cold drawn tubes?
In contrast, the cold tolerance capacity of the same specification tube is greater than that of the extruded pipe. Only cold drawing, the mold and its material requirements are very high, so cold drawn pipe prices slightly higher.
Q:Can 304 stainless steel aluminum pipe be welded with 6061?
304 stainless steel pipe6061 is aluminumWelding is difficult, it should not be fixed, consider other ways to butt it
Q:How can the fridge aluminum pipe trachoma be filled?
3., if the tube trachoma too much, you can cut it, re - replace a new tube, welded at both ends.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range