acm composite sheet building exterior wall cladding designs
1.Excellent fireproof property
1. acm composite sheet building exterior wall cladding designs
up to 5800mm,recommended:2440,3050,4050mm
1) front side: aluminum alloy sheet coated with fluoro-carbon resin(PVDF) or polyester resin (PE)
2) Core material: nontoxic polyethylene, PE, FR, LDPE
3) Back side: aluminum alloy sheet coated with polyester resin painting(PE)
a) Super peeling strength
b) Excellent surface flatness and smoothness
c) Superior weather, corrosion, pollutant resistance
d) Even coating, various colors
e) Fireproof, excellent heat and sound insulation
f) Superior impact resistance
g) Lightweight and easy to process
h) Easy to maintain, self-clean
- Q:Will the sheet metal processing bending coefficient and plate thickness, bending angle
- The bending factor and the thickness of the material you said bending angle ah bend the radius and bending the bending machine up and down mold, the length of the bending parts are related
We are using experience value. After all, conventional standard brick algorithm does not take into account the equipment wear and tear, sheet material thickness of the situation
Different thickness determines the different bending factors such as 1mm cold rolling fold 90 degrees and 2mm cold rolling fold 90 degrees
Our actual situation is 1mm coefficient is 1.8 2mm coefficient is 3.5
The same angle 90 degrees is a bending factor of 60 degrees is 1/2 of the bending coefficient of 45 degrees is 1/3 of the bending coefficient of less than 30 degrees according to the different thickness of the buckle or buckle a 0.5
Material and plate thickness as different materials, the bending coefficient is different
The bending radius is related to the bending machine. The standard single V or double V is even the default value of the other V slots.
But there are customers who need to be too small or a large bend radius will be specific to the analysis
Too small bend radius, our approach is to plan the groove to bend, so that the bending radius is very small, almost vertical right angle bending
Too large bending radius, the upper mold can be used on the corresponding arc on the mold (note that the upper arc of the R is the inside of your bending R, if the outside R according to the outer R minus a plate thickness to determine the model)
Or a large R30 50 or more, you can use a split bend, which requires the calculation of the cut-in angle and the last knife angle, as well as the size and angle of each knife
There is a part of the length of this I think a lot or machine equipment and related to our machine a long time 1.5mm stainless steel over 1m according to the case will not use 8mm mold bending
- Q:Plate furniture formaldehyde release national standard is
- The state for the wooden furniture, the release of harmful substances have a clear mandatory provisions, including plate furniture formaldehyde emission limit of ≤ 1.5mg / L.
- Q:What is the board for the speaker
- 200MM above the high-density board can be a little thick panel, do a good job after filling the sound-absorbing cotton
- Q:The production of melamine sheet
- Melamine decorative board performance:
Can be imitation of a variety of patterns, bright color, for a variety of wood-based panels and wood veneer, hardness, wear resistance, good heat resistance.
Chemical resistance, and can resist the general acid, alkali, grease and alcohol and other solvent wear.
Smooth and smooth surface, easy to maintain cleaning.
Because it has a natural wood can not both the excellent performance, it is often used for indoor construction and a variety of furniture, cabinets on the decoration.
Melamine board is a wall decoration material. It is not appropriate to use a melamine board counterfeit flooring for floor decoration.
Common specifications: 2135mm × 915mm, 2440mm × 915mm, 2440mm × 1220mm, thickness 0.6-1.2mm.
In the interior decoration, often used, do light furniture, long life, rapid processing of environmentally friendly!
The advantages of this plate is: the surface is flat, because the plate double-sided expansion coefficient of the same and not easy to deformation, bright colors, the surface more wear-resistant, corrosion-resistant, affordable. Domestic production of melamine trim door panels to Lushui River as the representative of the indicators are also reached the international standards.
Disadvantages: margin easy to collapse edge, glue traces of the more obvious, less color, can not gong flowers only straight edge.
- Q:Pc plate and memory board comparison, which is good?
- PC board is a polycarbonate as the main component, the use of co-extrusion technology CO-EXTRUSION made of a high-quality sheet. Because of its surface covered with a layer of high concentration of UV absorbers, in addition to the characteristics of anti-ultraviolet and can maintain long-term weather, never fade. Memory plate toughness is relatively large. Select these two plates according to your needs.
- Q:What is Fang plate
- Is the use of texture easy, the performance of heat, anti-burning, waterproof, moisture and other wood or compound synthesis of a kind of wood plate material after processing the width of more than 3 times the thickness of the plate known as the width of less than or equal to 3 times the thickness For the Fang material
- Q:What are the types of decorative plates?
- Decorative sheet types are blockboard, plywood, decorative panels, MDF, Glulam, Particleboard, Fireboard, Gypsum board, PVC sheet, Aluminum plate, Aluminum plate, 3D board. Xiaobian today to simply introduce you to Glulam and PVC sheet two common life of the plate.
Decorative materials are divided into two parts: part of the outdoor materials, part of the indoor materials.
Indoor materials and then divided into stone, sheet, sheet, profile, wire five types.
Decorative sheet is the general term for all plates, mainly: blockboard, plywood, decorative panels, MDF, Glulam, Particleboard, Fireboard, Gypsum board, PVC board, Aluminum gusset plate, Aluminum plate,
- Q:What is cold rolled plate ah? Cold rolled plate is a plate of no
- Simply put, that is, from the hot-rolled plate through the bell-type furnace or continuous annealing process, into a cold-rolled plate, the actual change is the physical structure of iron atoms, making it easier to bend, punching and other mechanical process The Cold rolled plate is only a basic plate inside the plate, after galvanizing, it becomes a galvanized sheet.
- Q:What are the qualifications required for imported timber?
- Imported wood and furniture are different.
Timber import normal declaration
Check the words do not need special approval is to provide foreign official phytosanitary certificate
Note that there is no soil and bark.
Provide certificate of origin.
- Q:Tatami table selection problem
- Hello, do not know where you are tatami, I have done 8 years and the room, I help you solve this problem bars. As we all know: plywood, Daixinban, MDF, etc. are high plastic content of the plate, but here also shows that the formal professional and room manufacturers will not use these plates! In the country, especially in the northern region, with camphor pine in particular, affordable, color texture and feel, by the majority of customers accepted. But here to explain is that even the board is still stitching Pinus sylvestris, the market even if there is a pure use of a full-page, you have to understand, but the choice of large manufacturers of the plate, the general formaldehyde content is controlled Within the scope of the national requirements. Sheet is a sheet, in addition to the column, beams, slide part of the open with a wooden side, and other are generally integrated materials. Speaking of environmental protection, large manufacturers of the plate will generally not use any problems, and then is the paint, paint the quality of the product determines the quality and service life, and the room is generally done varnish processing, is divided into topcoat, primer, And so on multiple processes. Paint paint to be smooth, visual no impurities, feel no bulging particles, film hardness is high. Also give you a recommended plate, that is, Ash.
Well, to say so much, the key is to choose the formal professional manufacturers, the current domestic and the room market quite a mixed bag, due to low access threshold, many couples mixed into them, the price war damage is ultimately the interests of consumers. You can go to the formal large-scale building materials store, choose a qualified regular manufacturers! I hope I can help you!
1. Manufacturer Overview
|Annual Output Value
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
|No.of Employees in Trade Department
|No. of Production Lines
|Product Price Range