ABB Original China High Low Voltage AC Motor

Ref Price:
Loading Port:
China Main Port
Payment Terms:
TT OR LC
Min Order Qty:
-
Supply Capability:
-

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Brand Name:ABBModel Number:HXR 560 SeriesType:Squirrel Cage Motor
Frequency:62.2 HzOutput Power:750 KWProtect Feature:Explosion-proof
Phase:Three-phaseCertification:CEAC Voltage:690V
Place of Origin:Shanghai China (Mainland)Efficiency:IE 1Packaging Detail::EXPORT STANDAR WOODEN CASE
StructureAsynchronous MotorFunctionDriving UsageUniversal








Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:how do i change the rotation on a g.e. 5kc49tg1255x ac motor?
Switch the red and black wires.
Q:What are the most common specs desired for industrial motors?
PS Note that there are standard no-load RPM ratings, but the full-load ratings on the nameplate are anywhere from 1 to 5% less than the no-load speeds and rarely more than 5% less. For 60 Hz the no-load speeds are 3600, 1800, 1200 and 900 RPM and rarely some values less than that. There are standard horsepower values like 1/4, 1/2, 3/4, 1, 1-1/2, 2, 3, 5, 7-1/2, 10 15, 20, 25, 30, 40, 50, 60, 75, 100, 125, 150, 200 and so on.
Q:what type of motor is this and can it be reversed?
It is a shaded pole motor and it is not electrically reversible, but, it may be possible to remove the rotor (loosen the two screws holding the bearings in place) and reassemble it with the output shaft on the other side of the frame which will result in the shaft rotating the opposite direction
Q:How we can connect two or more AC POWER SOURCE?
Can't do it, they will all have slightly different frequencies, which will result in very strange waveforms at the output, with beat frequencies. In addition, they will attempt to drive each other, with the result of one or more burning out. .
Q:Overvolting a DC motor?
Assuming it is a 1.0 service factor and the type is a series motor, you would get right at 1/3 more RPM depending on the load. Motors being so different, some like a little high voltage some like low voltage, about the only way to really know the current draw is to measure it. I would not allow it to run anymore than 10% over rated current. Next is the quality of the motor, some AC motors ran off VFDS run at higher speeds than rated, but again current and load will have a huge effect. But back to your extra 12 volts, the internal components are designed to withstand a certain RPM. However some motors are built to the bare minimum design, others are built to withstand some overload. It's a big jump, but again a series DC motor is load controlled, we don't know the load, and only by measuring it will we. I would say it the chances are the motor lasting is going to go down by the amount of the over voltage. I would suggest you use some type of mechanical transmission to increase the wheel speed which is what I assume you are after. Again this creates different loads, so find a DC amp meter so you know where you are at, and mount it on the kart, a volt meter would be nice also.. A larger driver pulley[or gear] on the motor shaft and a smaller driven pulley [or gear} will give you more RPM at the driven pulley. Just like an automobile, there are transmissions to control the RPMS of the engine, at various speeds along with torque at various speeds. If you go to a bearing supply store, they will have a line of variable adjustable pulleys that can be adjusted in or out to increase or decrease the diameter, you might find a device like that very helpful. Direct drive is smoother and dependent again on the motor, would be a great drive train but you are talking a very sophisticated and expensive motor and controller.
Q:We just changed the motor in my 99 cavalier and now the clutch for the ac will not engage. whats causing this?
did you plug the plug-in going to the compressor? if you unhooked the AC lines then you lost all the fluid for the AC. it won,t kick on if it,s dry or too low.
Q:How can I tell if a motor runs off of A/C or D/C?
It is an AC motor. The HZ mean hertz which is the frequency of the AC, in North America it is 60.
Q:can i use ac motor in windmill?
No
Q:What's the purpose of thyristor stack on ac motors?
To control motor speed.
Q:ANYONE know how to SIZE a SINGLE PHASE MOTOR to lift up vertically 150kg?
Depends on how fast you want to lift it. With the right gears a tiny motor will do the job, although it may take hours.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range