90 Degree Long Radius Stainless Steel Elbow

Ref Price:
Loading Port:
Tianjin
Payment Terms:
TT OR LC
Min Order Qty:
1 pc
Supply Capability:
5000 pc/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Stainless steel fittings are a kind of pipe fittings made by stainless steel. Thus it called stainless steel fittings, it includes: stainless steel elbow, stainless steel tee, stainless steel cross, stainless steel reducer, stainless steel pipe cap, etc., It can be divided into socket type stainless steel fittings, threaded stainless steel fittings, and butt-welded stainless steel fittings according to join method.Stainless steel elbow is used for fitting where changing direction, stainless steel tee to binding of three tube;Stainless steel cross  used to binding of four tube;Stainless steel reducer used for change of  diameter.

 

Product range

Elbows: LR&SR 45D 90D 180Dor in other degree
Bends: R=3D R=5D R=7D R=10D or as the clients’ requests
Tees: Equal & Unequal;
Reducers: Concentric & Eccentric
End Cap

Material

A403 WP304/304L; WP316/316L/316H;WP321,WP347Hetc.

Size

1/2”~24”; 26”~96”

Wall Thickness

 SCH5S~XXS

Standard

ASME B16.9, ASME B16.28, MSS SP43, DIN2605DIN2617DIN2516JISB2311,etc; or design as the clients’ requests;

Usage

Petroleum, chemical, power plant, gas, metallurgy, shipbuilding, construction, etc

Stainless Steel Elbow

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:What do you mean by the next connection in the pipe connection? How do you use it?
The professional name is only wearing a joint pipe through the wall, using a splint or interlayer
Q:What is the taper angle of flared tubular joints?
One end of the pipe is expanded to form an inner cone surface consistent with the cone angle of the pipe joint, the angle of the cone is 74 DEG, and the outer cone is the same as the angle of the inner cone of the pipe mouth, and the angle of the conical face is 66 deg.
Q:Stainless steel pipe, wire joint leakage how to make up?
What is the pressure in the pipe? The glue material is not blocked up, in the humid environment and water under the condition that the glue is not stick, reliable and economic way: cold metal flux were patching, simple and convenient, do not need what tools
Q:Standard Specification for jacket type pipe couplings for card sleeve couplings
25 1 33.5 3.25 32″×″1 / 1 / 4 31.75 1.80 32″×1 / 1 / 4 / 1 /″″32 1 4 42.25 3.25 40″×″1 / 1 / 2″×1.80 38.10 38(40)1 / 1 / 2 / 1 / 40 1″″2″48 3.5 50 2 50.80×″″×2 51(50)2″″50 2 60 3.5 70″×″2 / 1 / 2″×2.5 63.50 64(70)2 / 1 / 2 / 1 /″″70 2 2 75.5 3.75 80 3″×″″76.20×75(3.20 80)3″″80 3 88.5 4 100 4″×″″100 4 114 4″×
Q:Will that be all right? Then there's the PPR pipe joint on the right. Is that ok?
The theory of PPR hot melt connection is safe and reliable, more than a few joints do not affect the use, will not cause the day after Water Leakage, of course, the premise is the quality manual, technical standard master.
Q:PT1/4 large diameter pipe joint? No figure urgently
The thread has a taper of 1:16, equivalent to 55 degrees taper pipe thread, or ZG
Q:Press the hydraulic pipe fittings standard need to do what procedures
The corresponding micrometer scale is 3. Installed with 33mm mold on the mold seat, and rotated to 3 micrometer scale, the hose peeling and joint assembly. After measuring the joint outer diameter of buckling is buckling parameter table after withholding value 33.5mm is withheld. If the diameter does not conform to withhold, after a fine micrometer withhold hose. Withhold hose connector: swage size too much, hose layer broken, causing leakage; too little buckling size, and hydraulic oil spill caused by rushing out of joint.
Q:How do I distinguish the rigid clamp joint and the flexible clamp joint from the outward appearance?
Length and thickness of flexible clamps.Clamp itself difference:Flexible and rigid joints of the same specifications: width is different, flexibility is wider than rigidity 2MM (take 159 clamps as an example)
Q:The gas cooker joint is pagoda shaped. Can it fall down and connect with bellows joint directly?
Only when the thread and the sealing form are the same.The utility model relates to a gas cooker joint, which is an interface for introducing gas into a gas rangeA pagoda shaped joint of a gas cooker is a terminal joint used for connecting a hose to a device. It is only one of the many conversion joints used by the gas interface of the gas appliance to connect to the user's pipe
Q:Who knows what the clamp joint standard is?
But why are the actual products very much the same? Because the company is different and not all over the world. Where will it be?

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range