6W GU10 LED spotlight
3.Good heat dissipation
4.long lifespan more>50000hrs
Specification of 6W GU10 LED spotlight:
white/ warm white
Input:DC12-24V Output:3*1W Dimension:D50*H53MM Luminous flux: 250 Lm Beam Angle:30° 45°
Input:AC100-240V 50/60Hz Output:3*1W Dimension:D50*H62MM Luminous flux: 250 Lm Beam Angle:30° 45°
Input:AC100-240V 50/60Hz Output:3*1W Dimension:D50*H67MM Luminous flux: 250 Lm Beam Angle:30° 45°
Features of 6W GU10 LED spotlight:
High performance LED, up to 230lm for cool white and 200lm for warm white
Tricolor coating, evenly light spreading
Long life span, more than 50,000 hours
Low surface heating, less than 50°
Replacement for incandecent lamps
White and warm white available
Input voltage: 12 - 240V
Beam angle: 30° 45°
LED Spotlight Application:
Replacement bulbs for general lighting, especially for museums, art galleries, cosmetic counters where UV or IR radiation is undesirable.
LED Spotlight Payment Details:
Payment Terms: T/T
Minimum Order:50 Pieces
Lead Time:10 - 15 days
- Q:Adult science, starry sky projector, install the light bulb is not bright
- It is a simple circuit with a multimeter measure circuit, switch, lamp bulb, batteries
- Q:How to distinguish the true and false of projection light bulb?
- 1, look at the light bulb lamp wall, there is a group of real numbers, clear printing, suffused with soft and natural luster, and not easy to wipe off, this group of fake numbers because wear will incomplete, even if the re printed, gloss is also bleak, the handwriting is not clear, hard wipe will erase.2, a small lamp bulb above the iron pole, which is breaking the "lock" and lamp wick, old lamp replacement wick must do hands in this small iron head, "natural" and acquired installed there is always a little difference.However, as the craftsmanship is becoming more and more sophisticated, the two methods of identification are not entirely absolute, even though professionals may not be able to tell the difference.
- Q:What is a projection light? What's the use?
- he can in the wall, ground projection pattern you want to do advertising, decoration, warning etc.
- Q:Logo projection lamp with VR lighting performance, how can I get it out? Seek expert advice urgent...
- The word model is worked out, and then the self luminous material is then given to some transparency.
- Q:How to make a small projection lamp? emergency
- The most simple principle is to imitate the shadow, to good effect on the use of light through the light cast out. Asked too succinctly, I do not know how to answer. You too will unfailingly.
- Q:Where is the ocean projector that he sells to Zheng He in the Western Ocean?
- Take a look at the cultural markets around here
- Q:How do you do routine maintenance of projection bulb?
- Prevent repeated movementIn the projection process, we will definitely encounter the condition of adjusting the projection azimuth. At this time, many people will adopt the direct movement method to adjust to the appropriate position. But what we're going to tell us here is that it wasWhen the light bulb is in use, the temperature will be very high. At the moment, the filament inside the bulb is usually operated in semi molten condition. If the projection is moving frequently at this time, it will probably harm the projection bulb. Thus advocated,If it is placed in the projection, when we use the two or three best can be placed in position to determine the projection, such as non special conditions, we must prevent the move, so every time not only easy to use, but also reduce the direct harm to the projection.The projection bulb replacement / installation method is very elegantWhen the projection lamp needs replacement, we should immediately check the projector containing instructions, ensure the protection and replacement steps accurately; at the same time, buy the bulb, we also recognize that what the common type and the projector bulb can compatible, which is not compatible, if the selected fault type and may burn lighting, projection the lamp and projector.All objects on so precious, we usually use the best care treatment, carefully protected, it means only a maximum limit, extending life saving bulbs.
- Q:Why should an outdoor advertisement be patterned with glass?
- As is known to all, the advertisement projection lamp must match the pattern piece to be able to image. Therefore, the quality of the pattern film directly affects the projection effect.The patterned pieces are also called LOGO pieces, and the GOBO can be placed in a pattern projection lamp or a LOGO lamp to project patterns in the pattern.The material of the pattern piece can be film, iron sheet and glass piece.Film production is simple, short life, but poor light transmission, low contrast, not high temperature, easy to fade, change more frequently.
- Q:How about an outdoor projection lamp?
- (2) easy to make and installThe installation of the traditional light box is time-consuming and laborious, and consumes a lot of manpower and material resources, but it can not attract the sight of consumers for a long time. Dynamic projection advertising will help you save all the inconveniences and allow you to finish the tedious tasks in a short time.
- Q:Abroad, there is no curtain can be logo rotary projection lamp called what light?
- Zhengzhou Le Di Photoelectric Technology Co., Ltd is a technology oriented enterprise specializing in R & D, production, sales as one of the domestic and abroad, the main products for small and medium power LED projection lamp is suitable for indoor and outdoor advertising and halogen power projection lamp.
We have a number of well-known experts who have made outstanding contributions to many products which have applied for patents. We takes the principle "Quality First, Honor highest, service best" as her management idea.We will diligently and continually develop our products and perfect our service. All our efforts gain high appraisal from massive customers.
We hold the conception of 'Science &Technology as forerunner, long-term development as strategy.'
1. Manufacturer Overview
|Annual Output Value
||US$2.5 Million - US$5 Million
||North America; South America; Eastern Europe; Africa; Oceania; Mid East; Western Europe; Central America; Northern Europe
||ROHS-LED Tube; CE-Tube light; CE-Tube; ROHS-Strip light
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
||71% - 80%
|No.of Employees in Trade Department
||1,000-3,000 square meters
|No. of Production Lines
||OEM Service Offered Design Service Offered Buyer Label Offered
|Product Price Range