This surface-mount LED comes in standard package dimension.
It has a substrate made up of a molded plastic reflector sitting on top of a bent lead frame.
The die is attached within the reflector cavity and the cavity is encapsulated by silicone.
The package design coupled with careful selection of component materials allow these products to perform with high reliability.
1. Emitted Color: Natural White
CCT: about 4000K
Luminous Flux: 6.5-7lm
Luminous intensity: 2200~2400mcd @120 degrees
2. Lead frame: White
3. Suitable for all SMT assembly methods.
4. Compatible with infrared and vapor phase reflow solder process.
5. Compatible with automatic placement equipment.
6. This product doesn’t contain restriction Substance, comply ROHS standard.
1, 5050 smd led 18-20LM, 20-22LM, 22-24LM 2, 5630 smd/5053 smd led 40-45lm; 45-55lm
5050 white SMD led/ 5050 rgb
Color avaible:white , blue , greed, red,rgb etc
Vf: 3.0 to 3.6/1.8 to 2.2
View angle: 120degree
no decay in 1000hours
Estimated Delivery Time
2-8 business days
3-8 business days
2-10 business days
1-7 business days
6-14 business days
7-12 business days
China Post Air Mail
7-15 business days
China Post SAL
14-30 business days
3-10 business days
30-40 business days
1.3-5 business days for Sample Orders; 7-30 business days for Bulk Orders for Bulk Orders.
2."Business days" means Monday-Friday, excluding holidays.
3.DHL and UPS cannot ship to military or P.O. boxes address
4.The Shipping Service above is for reference only, for any other questions, please feel free to contact us.
Send a message to us:
Q:Welding method and notice of SMT LED
I recommend reflow soldering under normal conditions and manual welding only when repaired. 2 manual soldering electric soldering iron maximum power can not exceed 30W, welding temperature is controlled within 300 degrees, welding time less than 3 seconds. 3 do not touch the colloidal iron welding head. 4 when the pin is heated to 85 degrees centigrade or higher than this temperature, it can not be pressed. Otherwise, the welding will be broken.
Q:Which is good for LED patch and LED bulb?
Chip LEDLED patch lamp (SMD) is made of FPC circuit board, LED lamp and high quality silica gel sleeve. Waterproof performance, using low voltage DC power supply is safe and convenient, light colors, bright colors; outdoor use can be anti UV aging, yellowing, high temperature resistance and other advantages, the products are widely used in building lights, decorative lighting, advertising and entertainment quasi decorative lighting lighting field.LED bulbThe light emitting diode, is capable of converting electrical energy into visible solid semiconductor devices, which can be directly converted into electricity to light; LED Large Electronic = Display, LED = large electronic display; Lupus erythematosus disseminatus, systemic lupus erythematosus, a chronic idiopathic autoimmune disease; LED lead the past and past participle, meaning "leadership, led the Russian Pulkovo Airport IATA code.
Q:The quality of the LED patch module
Quality of circuit board. In the same quality of LED, the quality of PCB will have an important impact on the life of LED. The circuit board is divided into aluminum plate, glass fiber board, semi glass fiber board and paperboard. The quality of aluminum is the best, the best cooling effect, but the cost is too high, the domestic manufacturers generally only in high-power LED products use, LED module manufacturers generally use cardboard, semi glass fiber and glass fiber board. Module, piranha, straw hat module monochrome is generally used in cardboard or semi glass, commonly used glass fiber or semi SMD glass fiber board. Colorful and full color module series generally at least half of glass fiber, so as to match.
Q:Patch LED features
The principle of luminescence is that of cold luminescence, not by heating or discharging light, so the component life is about 50~100 times longer than that of tungsten filament bulb, and about one hundred thousand hours.
Q:Patch LED manual welding, how can welding not burn lights?
When soldering, the temperature is best to be lower, and the average welding temperature is about 360. That's enough, because the melting temperature of the tin wire is about 220 degrees, so if it is allowed, the temperature can be reduced as low as possible.
Q:What is the difference in performance between the LED plug-in and the LED patch?
The cooling of the plug-in is not good, because the plug-in's lamp foot, in order to save costs, generally use iron plus coating, heat conduction is not very good.The strength of aluminium alloy is not enough, it is easy to break, and copper is expensive.Relatively speaking, the patch is good, because the heat is welded on the PCB, copper or direct aluminum substrate cooling, patches near.Otherwise, why do high-power patch it?!SMT direct placement machine, a high degree of automation, low rate of bad.
Q:LED package and LED SMD LED lamp, what is the difference? Will the release agent be used in that part?
They differ in form and belong to the SMDLED category. Encapsulation uses liquid silicone and epoxy resins as well. The patches are basically made of epoxy resin. Relatively speaking, the amount of liquid silica should be relatively large.
Q:Why is the patch LED blue light dim?
The pressure drop of the blue light is greater than that of the red light and the green light. If the series connection is the same as that of the green light and red light, the current limiting resistor will tend to dim
Q:Patch LED market conditions
With good market expectations for the future status of SMD LED, all the major manufacturers have launched their own SMD LED development planning and prototype products, all of a sudden, SMD LED market showing a flourishing and lively atmosphere of contention of a hundred schools of thought.
Q:What is the difference between SMT LED packaging with silicone and epoxy resin transparent package? What is the market situation of these two types of packaging?
The main difference is the encapsulation method. The liquid silicone is mainly encapsulated and encapsulated, while the gum cake is solid and adopts a transfer molding package. Of course, there is a fundamental difference between the material, silica gel can be used for white light high-power LED, suitable for lighting. The epoxy can only be used in low-power monochrome LED, suitable for display, backlight, induction and other components.