4*185mm2 Power Cable Steel Tape Armoured

Ref Price:
Loading Port:
China main port
Payment Terms:
TT OR LC
Min Order Qty:
200 m
Supply Capability:
20000 m/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Product description of  Armoured Cable supplier

4*185mm2 Power Cable supplier Steel Tape Armoured

 

Brief Introduction

PVC/XLPE power cable is used to transmit and distribute power in power transmission and distribution system of 35kV or lower. It is generally applied to the fields including power, construction, mines, metallurgy, petrochemical industry and communication in complete replace of oil immersed paper insulated power cable and in partial replace of PVC insulated power cable.

Standard

The products can be produced according to our factory specification which is equivalent to the standard IEC60502.The factory can also design and manufacture special power cable according to the other standards required by the customers.

 

Properties of  PVC Power Cable

 

1.The long-time permissible working temperature of cable conductive core is not more than 70 degrees.

 

2.During short circuit (max permanent time is not more than 5 seconds), the max temperature of cable conductor is not more than 165°C.
3.The difference level of laying cable is not restricted.When laying the cable,ambient temperature is not lower than 0°C.
4.They have good chemical stability,and properties of acid resistance,alkali resistance,salt resistance,oil resistance,solvent resistance and flame resistance.

 

Properties of XLPE Power Cable

1.The highest allowed operating temperature of conductor for long-term working is 90 degrees.

2.In short circuit (Max long term is no more than 5 seconds). The highest temperature for conductor is no more than 250 degrees.

3.The cable is laid without horizontal drop limit. The environment temperature should be no lower than 0 when lay. Otherwise it should be preheated.

4.Excellent electrical performance, resistance to chemical corrosion.

5.Can stand advisable traction when laid.Can stand traction from Outside.Left low smoke halogen-free after burned.Retard the burning of the cable.

 

Nominal Cross-sectional Areas

1.5 mm, 2.5 mm2  ,4 mm, 6 mm, 10 mm2  , 16 mm,25 mm2  , 35 mm, 50 mm2  ,70 mm2  ,

95 mm2  ,120 mm2  ,150 mm,185 mm2  ,240 mm,300 mm  400 mm2  , 500 mm2  ,   630 mm2  , 

800 mm2

 

Production range

Single core cable: from 1.5 mm2  to 800 mm2,

Multi-core cable: from 1.5 mm2 to 400 mm2

 

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:PC turns on immediately after connecting power cable?
Hmm that sounds like you have missplaced the cables to the motherboard from the front pannel (on switch, HDD led etc.) Kenny
Q:Can we install control cable and power cable in one conduit?
Physically yes, but it is definitely not good practice. Normal practice is to segregate power and control cables. Local regulations may also prevent installing systems of 2 different voltage levels in the same conduit
Q:where can i purchase a power cable for my compaq laptop?
if you are a do it yourself guy try to get the plug at a electronic shop like Radio Shack and replaced yourself that will be the least expensive option, most adapters had the cable attached to the power supply so the next option will be to replace the power supply that will cost at least 60 dollars also try OKorder sometimes you get parts very cheap there.
Q:I need to know if i can use 550 watt power cables from my old amp to power my new 700 watt amp?
You can use them, but you won't get the most from your equipment. However, I don't think anyone will be able to tell the difference, it will be minuscule.
Q:Would a maxtor 320GB external hard drive work without a power cable if I connect it to the USB port?
Yes you need a power supply for all 3.5 inch drives. The laptop drives on the other hand will power off USB. Is this a SATA or ESATA drive? You can buy an enclosure for the SATA for around 35.00 and 70.00 + for a good ESATA enclosure. The cheaper ones do not work to well with the ESATA. If it's EIDE then you can get one off OKorder for around 12.00. Good luck.
Q:The power cable troughs are divided once and twice
Can be used for overhead, buried and pipeline laying of the cable line
Q:Stripping 4 gauge power cable?
I use a knife to strip that wire, just be careful not to nick the wire. Drill a hole and use sheet metal screws to screw the fuse holder down.
Q:What size secondary battery and power/ground cable should I use?
You can try the dealer for the exact cables for your vehicle, if they are not obsolete and are still available, no modifications required. But if shopping for aftermarket cables, longer may be better. You can always tie the extra cable up out of the way. If you start with a cable that is too short, you can't make it any longer. You want to make sure that the cables are not touching any hot engine parts, or crossing any sensitive wiring harnesses where electromagnetic fields could screw with electronic components. It may be better to let the local repair shop replace them for you.
Q:Formula of current carrying capacity of electrical power cables?
There is no definite safe formulas for your cables because it depends on many factors like what conductor . what insulation, how many cores ,what is your load , where is your load and ambient temperature and so on. The best guidance will be from the particular manufacturer who would provide the tables under various conditions as above.
Q:What is the best way to bundle audio cables?
any cable with an electrical current passing through will create an electromagnetic field. however when you bundle them in a single loop, because the currents are going in the same direction they will resemble a very big cable with a lot of current, so the magnetic field will be much larger (this is in part how an electric motor works). the best way to avoid this would be to remove excess cable so there would be no need to have loops. Really i'm not convinced about the benefits of having the cable in a figure 8 pattern, because it's just like having two loops really. i would try to avoid loops, or at least keep them away from the actual hifi and the speakers. generally components in your hifi and speakers will be magnetically shielded, to prevent any interference like that, however if you hear a buzzing noise when your mobile phone is near, than it's possible they're not shielded, as your mobile phone is a source of electromagnetic interference. if you're worried about electromagnetic interference it is also worth noting that wifi routers, mobile and cordless phones and microwaves are all sources of electromagnetic radiation. hope that all helps

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range