33111 Tapered Roller Bearigs Single Row Bearing

Ref Price:
Loading Port:
Shanghai
Payment Terms:
TT OR LC
Min Order Qty:
1000 pc
Supply Capability:
500000 pc/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Specificatioin of Taperder Roller Bearings:



The tapered roller bearing is to bear the combination of radial and axial load but mainly afford radial load. The loading capibility is determined by the raceway angle of outer  ring, the larger angle afford larger load. This kind of bearings can be  seperated and it can be divided into single-row and double-row tapered roller  bearings by the number of columns. The clearance for single-row tapered roller  bearing should be adjusted by the customers when installation. For the  double-row tapered roller bearings,the clearance has already set by the  manufacture before ex-factory. Tapered roller bearing has taper shaped inner  ring and outer ring raceway,and the roller elements arrange between them. All  projection lines from the surface of rollers meet at the same point on bearing  axis. This design makes tapered roller bearings particular suitable for combined  (axial and radial) loads.The axial loading capacity is determined by the  contacting angle α, the bigger angle for α, the larger axial loading capacity  is. Tapered roller bearing is usually a seperated bearing, that is,the inner  ring assembly including roller and cages, is seperated installed with the cup.



Taper roller bearings are mainly used for radial and axial joint load with radial load as main subject. Axial load capacity relies on raceway angle of outer ring: the bigger the angle is, the bigger the bearing capacity is. Outer ring can be separated and can be easily assembled. During installing and using process, axial clearance and radial clearance and radial clearance can be adjusted and pre-interference installation can be allowed. 


            


Product application:

In many applications tapered roller bearings are used in back-to-back pairs so that axial forces can be supported equally in either direction.


- car and vehicle wheel

- mining equipment

- moderate speed

- engine motors

- axle systems    

- construction

- agriculture

- reducers

- gear box



Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Can tapered roller bearings be joined together with two single row tapered roller bearings instead of double row?The altar,
3, load and life usually do not vary greatly, this is a personal opinion. I hope I can help you!
Q:Dimension parameter of thrust tapered roller bearing.
National standard GB 4663-1984, roller bearings, thrust cylindrical roller bearings, size, please check the mechanical design manual (Fifth Edition), second volumes --- commonly used rolling bearings, dimensions and performance parameters / thrust roller bearings.
Q:What are the E and Y values of the 30209 bearings of tapered roller bearings?
The shoulder of the positioning shaft is positioned; the transition shaft shoulder is provided for the disassembly of the parts on the shaft or the prevention of the stress concentration. But the axial shoulder will inevitably increase the diameter of the shaft, and the shoulder of the axle will change due to the stress concentration.
Q:Small problems of roller bearings of tapered roller bearings
Tapered roller bearing roller must have certain taper roller and raceway, inside and outside the vertebral vertebral vertex vertex must be of the same point and in the shaft center line (similar to bevel), or when the roller bearing motion reducer and raceway for angular velocity, linear velocity will be the same for different sliding friction and rolling bearing becomes sliding bearing.
Q:Can tapered roller bearings be installed in a vertical direction?
Whether horizontal mounting or vertical installation, the axial direction is axial and radial is radial
Q:Tapered roller bearing: Bearing expert why burned or locked
2, the bearing seat hole size deviation is too small or the size of the shaft deviation is too large, extrusion bearing ring deformation, make the clearance smaller. To burn locking phenomenon.3, bearing outer diameter and bearing seat hole, or between the bearing bore and the surface of the shaft between the foreign body, such as iron filings, burr, sand, cotton and so on. Will also squeeze bearing deformation, so that smaller clearance. To burn locking phenomenon.Bearing burnt lock. The cause of the accident can be analyzed according to the burning degree of the inner shell, the outer shell and the roller1. The inner shell burns most severely, the roller slightly lighter, and the outer shell almost does not change. After excluding the reasons for the nonstandard size of the inner bearing housing, the following judgment can be made.
Q:Tapered roller bearings in this case, how to use? Ten
Thrust bearing words. Thrust roller bearings can be used,
Q:How does the roller of tapered roller bearings fit in?
Tapered roller bearings in the production of equipment, it is the first roller and cage assembly, and then into the inner ring, composed of components. Tapered roller bearings as long as the assembly, even if completed the inner ring, because the outer ring is only one ring.I don't know if you'll understand.
Q:The installation of tapered roller bearings
1, for example, a shaft needs to be fitted with two such bearings at both ends. Can it be installed in the same direction?The force of the shaft is concerned. If the shaft is indeed subjected to one-way axial force, of course, it can be installed in the same direction. If it is subjected to biaxial axial force, it will not work
Q:There is a slot in the inner ring of tapered roller bearings, right? Is the roller in the slot?
There is a slot in the cone... The ball is placed in the slot. Handan, north, LiAskIs there a gap between the roller and the slot?Can I move axially?Chasing the answerThere is a certain clearance between them. It is not very large. It is caused by the force...

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range