Q:I just bought the 8800gt, but i don't have the cable to connect it to the power supply.So what cable do i need ??I found those but i am not sure

If you want to find out what cables you need there are two ways. 1. check the manual or guide that came with the device to see if it says what cables you need. 2. take the device with to a hardware or electronics store and ask the clerks there to help you find the right cables for you're device.

Q:which cables cant be near each other??(will cause noise radiation if put together)i gotta run some wires through my car and i dont know wich ones to keep away from others. im runnin...4 gauge (eventually will be 2 gauge) power wire for amp2 speaker wires for rear deck speakersrca cables for ampremote turn on wire for amp

NO it wont hurt nothing. Only reason you would have noise in rcas is if you got bad rcas. Only reason!

Q:Two things:1.) Why when we're using an AC to step up the voltage the power has to remain constant?2.) Why is it if we increase the voltage by a factor of 100 we have to decrease the current by a factor of a hundred and therefore I^2R is decreased by a factor of 10,000

Power is generated at the power station and transferred to the end user your home by means of power cables. Unfortunately, some power is always lost in this transfer process. It's power NOT Voltage OR Current that is required to operate your home electrical appliance. Yes, current and voltages are involved ;but it is the PRODUCT of these two that makes up the power NOT the voltage or current individually. Power = Voltage x Current Power is lost in the cables as heat as given by your i^2R. To reduce the losses then we must reduce the current I. But, if I reduce the current and keep the voltage the same then the power will fall and my kettle/Xbox/curling tongs will no longer work at home. So, to keep the power up when reducing the current I must compensate by increasing the voltage and this means using a step up transformer. Near the homes, a step down transformer is used to reduce it back down again. Since the losses in a cable are a consequence of I^2R heating then it is important to reduce the current as much as possible when transferring power. If we assume the the resistance, R of the cable is constant, then a 10,000 reduction in power (power/10,000) gives P/10,000 = I^2 x R I^2 = Power/10, 000R I = square root of [const x 10,000] I = 100. Then using power = voltage x current reducing the current by 100 means increasing the voltage by 100 to keep the power the same.

Q:Currently I have a 250GB drive and Writable CD/DVD. I wand to add a 3.51TB internal drive

You will have to get a SATA data cable. The power cable going to your current HD has a connector for a second drive. _

Q:Whats the Power Pass mean on a coax cable splitter?

It means it can pass DC current, such as used for satellite LNBs and amplified antennas

Q:power wont tuurn on from my amp there is power in the cables and i checked all fuses and wires there good to go nugga

The amp could be burnt out from the fans not turning on.

Q:It is a Gateway Desktop AMD Athlon 64X2 4200, 2048 DDR2, running Win XP Media center edition with Update Rollup 2. It first started when I put it in quot;stand-bymode and the computer refused to wake up. It has now gotten so bad I have to unplug the power several times with waiting periods in-between, before it will start up. I don't know much about computers but have been reading and trying different set-ups as I read about possible causes. If anyone can help, I'd appreciate.

its a dodgey PSU....get a new 1...( or take it to a shop and get it fitted if u dont know what ur doing)

Q:I had gave my amp a 16 volt input, then there was a spark which came from fuses that got burnt. I then replaced the fuses, rewired it nd gave it a 12 volt input it came on and went on protection. So i left it aside and after a few days i tryd connecting it again but this time it came on and it was burning the power cables no matter what guage wire i used. Any idea why its doing that?

Look for a short circuit in the input power circuitry.

Q:Will the YJV22-0.6 / 1KV5 * 10 (cable or wire model specifications) Will this model represents what cable diameter

GB-2002 provides: metal cable bridge and its bracket and the introduction or extraction of metal cable ducts must be ground (PE) or zero (PEN) is reliable, and must meet the following requirements:

Q:its like a big power box the has two metal prongs, and is about 2quot;X3big and fits into the same size slot, if you push it in it gets power for a second then doesnt if you jiggle it around it gets power for a second and doenst.anyone know please?

This okorder /