Q:How many volts is a single LED on the LED patch band?

The single LED on the LED patch band is around 3.3V.LED light emitting diode, which is a nonlinear component, its operating voltage (tube pressure drop) is also different: ordinary red LED about 1.5 V; ordinary green LED about 1.8 V; bright white LED up to 3.3 V or so.

Q:Notes on patch LED

Moisture proof, in order to avoid the products in the transport and storage of moisture, SMD LED packaging is moisture-proof aluminum packaging, and packaging bag containing a desiccant and humidity card, mainly to control the desiccant bag, humidity, humidity card is mainly to monitor the packaging bag of humidity

Q:The ten patch LED lights are connected in parallel. The rated power is 5 watts. How much voltage do you need?

Shunt split current series split voltageIs your single lamp voltage rated voltageIn addition to the red and green LED lights, the voltage is between 2 and 2.4, and the other colors are 3 to 3.6V

Q:Indoor full color LED display module and LED what is the difference between a full color?

The classification of the LED display according to the installation environment: indoor LED display screen, semi outdoor LED display, outdoor LED display; according to color: color LED screen, dual color LED display screen, LED display screen, the color LED display screen; according to the functional area can be divided into graphic screen, screen, screen, screen, digital dot matrix digital hybrid screen.

Q:Production of a number of substrates, the use of SMD LED lights, red lights and green lights are not bad, blue lights appear mass dark, do not know why? Is the LED blue light material easy to use dark?

If you choose the brightness of blue light in the light of the relatively high, so when debugging the white balance (by changing the resistance to change the current, and then change the RGB brightness LED lamp), it is difficult to transfer to the pure white. Therefore, when selecting the lamp, the blue light is generally not bright.

Q:Such as title, please have welding patch LED lamp experience expert guidance, do not search from the Internet to the theoretical knowledge, thank you!

If the power of the lamp, because heat high power do very well, so not good welding, the temperature at the highest (300 degrees), the use of horseshoe iron head, not waiting to solder, because the heat is very powerful, quick action.

Q:How to detect LED SMD beads

Resistance voltage ordinary pointer table 1.5V in general, and some only in the high resistance file (*10K file) with 9V or 15V battery, so the pointer table to measure LeD beads to hit the highest resistance profile measurement, otherwise useless, of course, at this time the brightness is very small, can not see, can only to judge the positive and negative resistance values see.

Q:LED light SMD LED package in what form, trouble you under the guidance of...

Draw your own line, mm is replaced by mil on the line, with vernier caliper measurement, or know the model, count the number of mil. For example, 5050 is a close square with a width of 5.0mm*5.0mmInline LED (such as straw hat lights, 5mm), piranha LED, surface mount LEDSinglechip collection from hardware to software chm

Q:LED patches have several ways of welding. Which ones can be reflow? What can be done by eutectic welding? Is the welding of viscose and lens material is required?

SMD patch products basically can be used in reflow soldering, especially a little note here that the eutectic welding is the connection between the chip and the substrate support or specifically, is the bottom of the chip after completion of production of coating material and a layer of Sikkim alloy, and then set up a heating zone in solid crystal machine package in time and a temperature of about 300 degrees, the realization process of the chip at the bottom of the Sikkim alloy melt and silver plated layer connection bracket, and a clear distinction between reflow.

Q:What are the storage requirements of SMT patch LED (LED)?

Keep in storage- the original sealing bag packing in the condition of the <40 C and <90% RH degrees for 12 months, more than the storage period will bake.Please check the leak before opening the packing bagIn opening the sealed bag, should be placed in SMD LED and C 60%RH. < < 30 degrees under the conditions in the above conditions, SMD LED must be in the open package using reflow within 24 hours. If placed more than 24 hours, you need to bake- baked, SMD LED in C + 80 degrees 5 degrees C and <=10%RH relative humidity in the oven for 24 hours? remove the pouch before baking, and do not open the oven door frequently