250W CNBM Monocrystalline Silicon Panel for Home Using

Ref Price:
Loading Port:
Payment Terms:
TT or LC
Min Order Qty:
500 set
Supply Capability:
10000 set/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

250W CNBM Monocrystalline Silicon Panel for Home Using


Production description


solar depending on the way they capture and distribute solar energy or convert it into solar power. Active solar techniques include the use of photovoltaic systems, concentrated solar power and solar water heating to harness the energy. Passive solar techniques include orienting a building to the Sun, selecting materials with favorable thermal mass or light dispersing properties, and designing spaces that naturally circulate air.

The large magnitude of solar energy available makes it a highly appealing source of electricity. The United Nations Development Programme in its 2000 World Energy Assessment found that the annual potential of solar energy was 1,575–49,387 exajoules (EJ). This is several times larger than the total world energy consumption, which was 559.8 EJ in 2012.

250W CNBM Monocrystalline Silicon Panel for Home Using




1.High conversion efficiencies resulting in superior power output performance.

2.Outstanding power output even in low light or high temperature conditions

3.Optimized design for ease of soldering and lamination


Physical characteristic


1. Rigorous quality control meets the highest international standards.

2. High-transmissivity low-iron tempered glass, strong aluminium frame.

3. Using UV-resistant silicon.

4. IS09001/14001/CE/TUV/UL  



26pcs in one carton 6pallets in 20foot container 14pallets in 40 foot container.

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:asus sabertooth power connectors?
For big fans that draws relatively large amounts of current (compared to smaller fans), you really should connect them to the PSU molex connectors using adapters. The motherboard fan headers can't handle much current, and larger fans WILL burn them out. Don't ask me how I know.
Q:How to connect my Graphics Card with my psu 6+2 pin power connector?
i doesn't problem with a GT220 or GT240, they are not a lot more effective useful if not worse than the cardboard you've already. those are not gaming playing cards, they are specially for video accelerating etc. Get a HD 4850 in case you'll locate one, if not perhaps a HD 5750 which gives you similar performance, yet i doesn't flow above this as you'll start up to be bottlenecked by technique of your processor. maximum playing cards in ordinary words take one 6pin connection, the in ordinary words exception being the proper end playing cards including the Nvidia GTX 470 or ATI HD 5870. desire i have helped ;)
Q:Which connector will be the best among these at 437 MHz?
Type-N will be the most suitable. These connectors work well at frequencies extending into several GHz. Moreover they show extremely low SWR at 437 MHz. Also, they are threaded connectors. So, there will be very low air dielectric loss. Apart from these, N-type is slightly moisture resistant, can handle high power and also are leakage resistant at RF. Most importantly, it needs simple manual screwing action to fix these connectors into the coax! BNC are extremely lossy at 437 MHz especially because they are non-threaded connectors and so will produce dielectric losses. Type-F connectors are usually used in TV connections. APC-7 is undoubtedly the best among these but the job will be very well done by N-type at 437 MHz.
Q:Does anyone know the typical attenuation of a RF SMA Connector?
Ain't much (negligible), which is why it's probably never spec'd, but the question and any answer is meaningless until we've got a frequency nailed down. The cable will represent the largest portion of any attenuation, and will swamp anything the connectors would contribute. The typical coax for SMA (RG-174, RG-188, RG-196 or RG-316) runs on the order of 60~80db/100' loss. Even the semi-rigid cables have a lot of loss in the microwave freqs. Decent SMA connectors are good to around 12.4GHz with flex cable, and 18GHz with semi-rigid cable. Some very special (and a bit expensive) ones are available for use up to the 26.5~27GHz !
Q:question about db15 connector cable?
The db15 extension cable should have a female connector on one end (with holes instead of pinsthe end of the cable connected to the monitor attaches to that end) and a male end on the other (with pins in the connectorthat end connects to the video adapter on the computer).
Q:What is the part number for the MAP sensor connector on a Jeep Grand Cherokee? ('93-'98 ZJ)?
why okorder
Q:PS/2 connector??????????????????
there are some mobos out there which have one PS/2 connector green and purple, this means they can support both keyboard and mouse! note: old mobos have 2 PS/2 connectors, greenmouse and purplekeyboard!
Q:Where do I find the PIP Connector?
the PIP (profile ignition pickup) connector is in the wires coming off of the distributor. it is really close to that area, with in a few feet. it is not much more than a small plastic connector the last time that i saw one.
Q:How much is a Wii Connector for the internet?
I think your thinking of a usb connector for wi-fi 49.95$ probly And Brawl is 49 dollars
Q:what is ethernet connector?
The ethernet connector is a port usually located on the rear of your tower next to the other plug conncetions. It looks like a port for a telephone wire, but bigger. I would be used to either connect your PC to a network, or a high speed modem (DSL etc.) If you connect to the internet with a dial up modem, no worry as you are not using the ethernet. IF you are trying to hook up to a DSL or other highspeed internet and it is saying it is not found you need to do something. So if you are not using it, and dont plan to, you can disable it. Go to start, Control panel, system, click on the tab for Hardware then the tab for device manager Probably next to what is not working there is a yellow question markclick on the little + sign to open the device, right click on the device and choose to disable it, close all windows and restart your system. Likewise if you want to use it, it might be disabled already, go through the same steps, but enable the device. Or you might need the driver for the device. Good luck

1. Manufacturer Overview

Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range