Φ219~Φ711 CFOE mill roll forming machine
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 set
- Supply Capability:
- 100 set/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Φ219~Φ711 CFOE mill roll forming machine
Φ219 Φ711 CFOE mill is the newest product in our company, which adoptsCFOE patent technology from our company. CFOE means continuous flexible formingand straight seam submerged arc welded pipe. There are special advantages inthe mill. The mill is continuous production, which is no need to change therollers in rough-forming section when the specification needs to be changed.Compared with ERW, the quality and energy consumption of CFOE is easier to becontrolled, and is welded better and low consumption. The welding seam of CFOEovercomes the shortages of long welding seam and difficult inspection on spiralwelding seam after inbuilt. Compared with UOE and JCOE, the investment cost andproduction cost are low.
The quality of CFOE welding seam is the best in allwelding seam technology. CFOE is the most reliable, and there is no circularinterface welding seam on the pipe, which is easy to weld, inspect, maintainand repair. The pipe produced by the mill just covers most pipes which are currentlyused by oil, gas casing. The mill also has a good market prospect. Annualproduction capacity is 50,000-100,000 tons.
If there are smalldifferences between CFOE cost and spiral welded pipe cost, nobody will buyspiral welded pipe on high grade pipeline. CFOE welded pipe will replace fullyspiral welded pipe in high grade pipeline, and have a good market prospect.
CFOE can be the complementmill for the JCOE mill. Because it is hard and uneconomical for UOE and JCOE toproduce the pipes within the diameter range of Φ219~Φ711. There are outstanding advantages such as less productioncost and high production capacity. Due to low production capacity and over highprice of JCOE mill, which create the serious competition problem, it can makeup middle and large diameter in JCOE.
1.Suitable material | Color steel sheet , galvanized steel sheet,aluminum sheet |
2.Installation Dimension (L*W*H): | 6.5m*1.5m*1.4m |
3.Main motor power | 3KW with Cycloidal reducer |
4.Hydraulic station power | 3KW |
5. Hydraulic oil pump | CB-E 310 |
6.Thickness of material | 0.3mm~1.0mm |
7.Diameter of principal axis | Φ70-90mm |
8.Material expand width | 1000mm |
9.Electric tension | 380V 3phase 50HZ or as the customer's requirements |
10.Material of roller | High grade 45# forged steel plated with hard chrome plating |
11.Controlling system | PLC |
12.Processing speed | 3-6m/min |
13.Processing precision within | 1.00mm (depend on design) |
14.Material of cutting blade | Cr12 mould steel with quenched treatment |
15.Kind of drive | 0.6 inch chain link bearing model 6210 |
16.Roller station | 8-20 Rollers |
17.Roller material | high grade 45#steel; Cr12 quenching |
18. Leak frame load-bearing | 4.6T |
- Q:What is the surface rolling forming machine process?
- The rolling process using metal at room temperature, cold plastic characteristic, through the rolling tool is the rolling tool to put some pressure on the metal surface, so that the workpiece surface by plastic deformation, the height to the lower tissue slip, the surface roughness decreased.
- Q:Improvement in rolling forming process
- The rolling will produce a hardening layer on the surface of the workpiece. This layer has obvious delamination phenomenon with the internal material, which is easy to cause the surface layer to fall off;
- Q:A roll forming machine, rolling out of the length is always not up to a fixed size, not too small, that is, more than that, what is the cause?
- Yes, the width of the bearing plate can be a deviation from the length.
- Q:What kind of material and what heat treatment are used for pressing roller (molding, feeding, cutting force, heavy load, heavy load) of sheet steel rolling machine?
- Use 40Cr or 20Cr, Cr12.Cr12MoV, quenching and tempering treatment, think of hardness, high point, carburizing, nitriding, and consider adding lubrication device to extend its service life
- Q:Process mould for rolling forming process
- Rolling forming is more complicated and requires higher than rolling thread. The die design is based on the different shapes of the workpiece, the design of the rolling plate into a cross section or a few sections, can use synchronous type; also can use grading type.
- Q:What is rolling forming processing?
- A special rolling tool is used to exert certain pressure on the surface of the workpiece so as to make the surface metal flow.
- Q:Material and equipment for roll forming process
- Rolling molding is usually through upsetting a blank cold heading machine, thread rolling machine rolling after processed. The equipment for thread rolling and rolling forming includes various reciprocating flat rolling machines, planetary wire rolling machines, two cylindrical roller spinning machines and three cylindrical roller spinning machines.
- Q:Introduction of roll forming process
- Not only threaded fasteners industry applications, automobiles, bicycles and other industrial sectors also use rolling forming process, processing complex shapes of parts.
1. Manufacturer Overview |
|
---|---|
Location | |
Year Established | |
Annual Output Value | |
Main Markets | |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | |
No.of Employees in Trade Department | |
Language Spoken: | |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
Φ219~Φ711 CFOE mill roll forming machine
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 set
- Supply Capability:
- 100 set/month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Related keywords