Q:What is the difference between steel and PVC gussets?

In fact, good PVC in the room can also be used 10 years later. (The above is not a direct roof tiles, PVC fear of hot steam) plastic just too expensive, and the price of PVC check a lot, PVC20 multi-buckle on the very good. I am a carpenter, these lives are done every day, so my heart there are several. Add (aluminum buckle board is not suitable for the top, only some positive, such as escort, advertising box)

Q:What is the difference between acrylic and PVC? Which is relatively better?

Acrylic better, you can light, the price is higher PVC easy to crack, fade, prone to scratches, the price is cheaper

Q:Pvc board ceiling installation method which know? How much is the installation cost?

1, according to the design elevation in the wall around the wall, the ball line should be clear, accurate location, the level of tolerance ± 5mm. 2, along the elevation line fixed edge keel, the role of the keel is the edge of the ceiling seal, side keel commonly used specifications for the 25 * 25mm, the color should be the same with the PVC buckle, the keel with cement nails fixed on the wall. The following are the same as the " 3, to determine the keel position line, because each piece of PVC gussets are already forming decorative panels, generally can no longer cut block, in order to ensure the integrity of the ceiling and installation reliability, according to the size of aluminum plate, and The size of the ceiling to arrange the structure of the ceiling skeleton size. The basic layout of the PVC gusset finishes is: the plate combination to be complete, surrounded by the edge, the edge of the edge to be symmetrical, will arrange the layout of the dragon frame line drawn on the top of the line. The following are the same as the " 4, the main keel hanging point spacing, according to the design recommended series selection, the middle part should be arch, keel arch height is not less than the room surface span of 1/200. The main keel should be installed in time to correct the location and height. To control the formation of the dragon frame, first of all should be pulled out of the vertical and horizontal elevation control line, starting from one end, while the side of the installation to adjust the boom suspension height. To be a large flat, and then some of the curved Alice of a single keel to adjust until the smooth meet the requirements so far.

Q:Has anyone tried this? I need to use it for a window that is 8'4 wide and due to the construction of the ceiling (concrete) and window frame (metal) I can't put in any center support. What diameter pipe did you use and what is the width of the window you used it on? Any tips/tricks?

bad choice, the PVC will give more then a metal rod, select a metal curtain rod and use self tapping screws to mount your support bracket on the metal frame.

Q:Is PVC flooring a plastic floor?

Professional PVC plastic floor construction 25 yuan / ㎡, with interface agent DC flat glue construction

Q:PVC plastic plate dirty how can quickly wipe clean?

Wash with toothpaste with a toothbrush Because it is not a big thing, you can simply use a toothbrush stained with a little toothpaste and then gently wipe it again until you can clean up. This can also add flavor to the bag.

Q:How to quickly tear off the protective film on the PVC board

Use the hair dryer to heat, hot, very good to get. The whole board about to tear up.

Q:Pvc floor with what glue

It depends on the use of places and the environment to choose, but also depends on the floor category to choose. As you use the PVC sheet flooring, the use of water-based sheet glue, the use of PVC coil floor, the use of water-based membrane glue. If in ordinary areas, the general water-based glue can be, and if in wading places, you must use two-component epoxy resin. Different floor thickness and physical properties, the choice of glue is also different, poor floor stability, the need to choose a higher cost of strong adhesive glue, the floor stability is good, but you can choose ordinary glue.

Q:Pvc board and pp board that is a lot of color, the kind of more suitable for kitchen and toilet waterproof furniture, furniture for the density of the board, specifications and other parameters are generally how much, about how much the price, China Province and the surrounding area Where can I buy this type of plate, the phone number is how much (I need is 1.5cm, 1.6cm and a small part of 1cm and 2cm of the plate)

PP can be used to do furniture,

Q:Pvc material plate how to weld?

10mm plate first to play around the mouth, the board fixed, and then double root pvc welding rod welding, welding at least three times, the best six times, the weld to protrude, the best between the electrodes without pores.