Q:Our concrete slab for the porch was poured after the house was built and concrete was splattered on a door. How do we go about removing it without damaging the paint? Sandy :O)

Concrete Splatter Removal

Q:Titanium alloy door quality how

The so-called titanium alloy doors are aluminum alloys. Surface made of hard anodized. Quality distinctions If you look at the surface finish, profile wall thickness. Good quality is good, and the thickness of the wall is good

Q:How to clean aluminum doors and windows? Make it a new look.

1, in the clean aluminum doors and windows, do not step on the aluminum frame, do not pull the box for support. So easy to wear the doors and windows or their own accident. 2, aluminum doors and windows can be used soft cloth stained with water or neutral detergent, do not use ordinary soap and detergent, but can not use decontamination powder, toilet and other strong acid and alkali cleaning agent, this will corrode the profile surface. 3, sealed tops and glass glue is to ensure that the aluminum doors and windows sealed insulation of the key structure, if the fall to timely repair, replacement. 4, after the rain, should be wiped in time wet glass and window frames. 5, should always check the doors and windows frame connection parts, tighten the bolt in time to replace the damaged parts. Positioning pin, wind support, to spring and other aluminum doors and windows of the vulnerable parts, to always check, regularly add lubricants to keep clean and flexible. 6, aluminum doors and windows in use, the action should be light, push and pull its natural; found difficult not hard pull hard push, should first rule out the fault. Fouling, deformation is the main reason for the difficulty of push and pull of aluminum alloy doors and windows, to keep the door frame clean, especially the sliding slot cleaning. Vacuum cleaner can be used to suck the tank and the door closed the fouling. 7, often check the aluminum window frame wall joints, the long time aluminum doors and windows if loose so easy to make the overall deformation of the frame, so that doors and windows can not be closed, sealed. So the connection of the screw loosening should be immediately tightened, such as screw feet loose, the application of epoxy strong glue to adjust a small amount of cement seal.

Q:Buy aluminum doors and windows to pay attention to what?

I am the decoration of this, it depends on where you live, and in the balcony to consider the appearance of fading, and whether it can withstand the invasion of sand. Installed in the toilet bathroom to think about whether the waterproof anti-electrochemical corrosion or something. There is also attention to noise isolation, thermal conductivity and other issues, such as the summer heat fast, then you do not open air conditioning, the same winter. These details should be taken into account. As for what brand is good, see how much you budget is slightly, the general luxury, villa decoration are like to use to send the doors and windows, if you have money, you can consider.

Q:I just upgraded my speakers in my car. The new ones are slightly bigger, so the magnets are almost touching the metal. Is this bad?

i put in extra than a number of audio equipment and the magnet interior the speaker continuously pulls and gets linked to the vehicle and so a procedures none of them sound and distinctive then what it looked like on the shop no strange static or something

Q:what kind of brush to use.

Make sure the door is preped good. Its not about the brush but more about the paint! The paint should be an outdoor paint suitable for metal applications! Good luck!

Q:My dog bent off this hard -tile like strong metal-vinyl which is my door. So Now a piece is sticking out and insulation beads are falling out. Where do I buy these metal/vinyl doors? I looked on Home depot but I only saw wood doors or metal screen doors. If it is going to be expensive($300) then I will just leave it like that and let them take my deposit because my dog messed up the carpet. (the door is a white door with rectangle imprints.Thanks

Home Depot carries them,You may have to get a pre-hung rather than a slab. You will be better off going to a door store as it is not as simple as popping a door off and popping a new one on. You have to mortise for the hinges and bore out the door for the lock set and deadbolt. You may find an exact fit,but the chances are slim. And no It wont be really cheap.

Q:also have 2x8s to frame it.

Assuming your door is pre-hung, measure the jamb width (not the molding attached to the face of the jamb). Add 3 1/4 inches for your 2x8 lumber, ( you did buy treated didn't you?). Add another 1/2 inch for room to plumb the jamb in the opening. (I'm afraid you have to go back to the store to buy shims...get some great-stuff for doors and windows while you're there.) Measure height of door jamb. Add 1/4 inch for leveling. Mark wall using level. Cut blocks with concrete saw you rented while you were out buying shims and great-stuff. Pray wall doesn't tumble down on your head, ( You did remember to consult a qualified engineer. It's much better if you pay them to take the blame when things go wrong.) Fill voids in wall with mortar or cement. Tapcon treated 2x8 to opening using a generous amount of liquid nails I forgot to tell you to buy. (Back to the store again...you actually had tapcons and a hammer drill?). Finally...the door. Get out your six foot level and your three foot level. Shim bottom of door on hinged side about 1/4 inch. Plumb hinged side up shimming as needed. level across top. Plumb down other side. Use shims behind every screw. (You did buy screws). Fill voids with great-stuff. Caulk. Paint. Lightly oil hinges. Enjoy :)

Q:Aluminum alloy doors and windows broken bridge and what is the difference between ordinary materials

Conventional aluminum alloy profiles because it is the whole body of aluminum alloy material, easy to heat the formation of thermal bridge effect The broken bridge aluminum alloy profile is based on the old aluminum alloy window in order to improve the performance of doors and windows insulation and the introduction of improved. Broken bridge aluminum alloy window principle is the use of PA66 nylon indoor and outdoor two-layer aluminum alloy is separated and closely connected into a whole, the connection can be divided into different ways to wear and type, with this profile doors and windows , Its superior heat insulation, completely solve the aluminum heat conduction fast, does not meet the energy requirements of the deadly problem, while taking some new form of cooperation with the form, completely solve the "aluminum alloy sliding window seal is not strict"

Q:I have two small children who can unlock the front door along with the dead bolt. I was going to put a chain lock on until I noticed the door is lined with a metal frame. I live in an a apartment so i cant just drill through it. What can i do? Thank you

You can get a simple slide bolt and mount it on the jam only. When you slide it over it will stop the door from opening. BUT just like a double cylinder dead bolt with no key available your kids can't get out in the case of a fire. Good Luck