Q:I have a 95 Buick Century that gets a bad vibration when the TCC engages. This vibration goes away if the car downshifts to accelerate or coasts. I already replaced the CV axles as it was suggested originally that they may have been responsible but now it's looking like the TCC is bad. I'm looking for the electrical connector that goes to it to see if the problem goes away with the TCC disabled.

The connector is usually just above the pan on the transmission. A 95 likely has an E series transmission which means that the same connector will also have the other transmission controls in it. If you remove that connector the transmission will stick in 2nd gear and your engine wont run correctly because the computer thinks the transmission died.

Q:I have just purchased one of these and noticed that the power supply has only 1 X 24 pin, 1 X 4 pin, 1 X sata, 1 x Mini plug and 4 X molexI need to power the following:My 9800 GTX+ 512MB with 2 PCIe 6 pin ports how should I go about powering this?and my 2 hard drives both use sata but i only have 1 sata power supply so how can i power these? Please nobody say a new PSU because I have only just bought a new one. And also the power supply neds to be stable and it's a 750W psu btw.ThanksKiz

you need a few power adapter plugs you can get a dubble molex to 6 pin. Then a molex to SATA. I find it unusual you didnt get the power adapers with the video card and a PSU at 750W with out the two 6 pin and so few plugs is a bit strange

Q:I am looking for a very specific center pin DC coaxial connector for my laptop power cord. I have an Alienware M17xR3, I know it is probably a LONG, very LONG shot that i find one online, but $3 is better than the $130 it is to replace it. I don' t have the proper caliper to determine the actual size, but based off a ruler.70-.80mm Outer diameter .50-.60mm Inner Diameter

wtf just find one or a charger on OKorder

Q:I have a dynex PC monitor extension cable and a friend of mine is looking for an extension cable that would connect to a video card, but i am not sure if it will.this friend doesn't live in town - so i can't just check it easily.suggestions? comments? ideas?

The db15 extension cable should have a female connector on one end (with holes instead of pinsthe end of the cable connected to the monitor attaches to that end) and a male end on the other (with pins in the connectorthat end connects to the video adapter on the computer).

Q:Hi, I have an old battery (kan 5w05337) that I'm trying to use. The connector is white plastic rectangular, about 1/3x1/2x1/4 with 3 connectors, 2 round and one square. I need the matching (male) adapter. Any hints on where to get one would be great. Also, the wiring is black, yellow, red (on the square). Anyone know what yellow is for? (Are there 2 circuits?) thanks!Eric

place the info on the device on Google search. you will be directed to many sites.

Q:I have a ceiling fan with a six pin molex connector. The wire colors are black, brown, gray, white, red and white. There is also a single separate wire with a cylindrical connector that is blue. Does anyone know which each wire is? I want to either buy/fabricate a light fixture to connect but need to know what the wires are.

I think that if you look closer you will find a white wire with a cylindrical connector on it. That and the blue are the wires you need to connect to a light kit. If you still have troubles try the manufactures web site for a wiring diagram. I have installed several hundred fans and light kits. Only a few of which had a factory installed multi pin plug designed for the light kit shipped with the fan.

Q:I have a 120mm computer fan which doesn't have a regular fan header instead it takes in a 4 pin power connector directly from the power supply. How can I convert a 4 pin power connector into a regular 3 pin fan header. I have extra parts from broken fans and extra 4 pin power connectors so I can easily solder some stuff up, or if a adapter exists what is it called?

u dont need an adapter it will run fine with the extra pin hanging off

Q:I’m replacing the existing light switch with a built-in timer, but I have a problem: I cannot use twist-on wire connectors as they occupy too much space in a switch box.Is it safe to use just an electrical tape?

this is against the national electric Code to splice wires in this manner. the only genuine problems I see right this is: a million) Butt-splices are no longer made for everlasting abode wiring. they do no longer seem to be an authorized technique for splices. 2) your place catches hearth. The plastic around the butt-splices will soften, however the metallic will nonetheless be seen related to the twine. as quickly as the hearth inspector nicely-knownshows this, it won't count number in the event that they have been the reason for the hearth or no longer, it is going to bypass onto the checklist this is sent on your insurance organisation. And all of us know the place this might bypass. The insurance organisation will look for any reason to reject a declare. (and working wires on superb suited of rafters has been a typical prepare for a protracted time, with the aid of fact the code adjustments each 3 years, so what could be criminal interior the 2005 code wasn't criminal interior the 2008 code.) 3) Any splice SHALL be in an UL listed enclosed field. I applaud you for asking the question. i'm hoping you may stay with your restoration. stable success and could God bless.

Q:I have a 06 nissan titan and i recently bought fog lights but my truck isnt wired for them so i need to make my own and i wanted to know what plug will fit on the fog light they told me the gm connector will fit

Look again most times there are factory plugs taped to the harness. If not PIAA OR Other brand of fog lights have harness relays and switches. Generic fog light bulb connector sould work.

Q:I am trying to learn about computer hardware in one of my IT classes, but some of this crap is confusing. My professor wants examples of each of these kinds of connectors:DIN, USB, FireWire, DB, RJ, and Audio I'm not really sure how to answer the question though. I mean I know about USB and firewire but thats about it, can anyone help me out? he wants 3 examples of each. Thanks so much to anyone who can help me.

DIN - PS2, old keyboard connector DB - RS-232, printer (parallel), game connector RJ - phone jack (handset, line, 6 pin), Ethernet Audio? Almost anything. Canon, PL, mini-PL, RCA, banana plug, pin plug, DIN, RJ-12 and RJ-14 are used for audio