Stainless Steel Pulley

Hot Products

STEEL PULLEY V-pulley ; Pulleys ; V belt pulleys SPZ,SPA,SPB,SPC

Cast Iron SPA V-Pulley with Taper Bush stainless steel guide pulley for passing steel wire

stainless steel guide pulley for passing steel wire,for sales manufacturer made in china

YANMAR diesel Engine spare Parts yanmar genuine parts 4TNE94 129916-21680 v-pulley

Steel v-pulleys SPZ SPA SPB SPC CONVEYOR CHAIN

Adjadjustable speed v-pulley STEPLESS VARIABLE SPEED PULLEYS

Steel V-pulley wheel timing pulley V-pulley ; Pulleys ; V belt pulleys SPZ,SPA,SPB,SPC

Adjadjustable speed v-pulley Small Stock Bore V-pulleys

Steel v-pulleys 4TNE94 4TNV98L Engine Parts V-belt pulley

V-Pulley SPA 80-1 1210 CNC Machining V-Pulley

FAQ

When the coupling is linked, can the drive shaft be thinner than the motor shaft?

Actually, the problem is mechanical mechanics.On the one hand, the size of the drive shaft in addition to considering the matching of the motor shaft

What part of the transmission mechanism of the walking conveyor?

Reducer selection principle: (1) according to the mechanical strength to determine the reducer specifications. Deceleration rated power P1N device is in stable load, work every day is equal to or less than 10h per hour, 5 times to start, allowing the starting torque for the contact strength safety factor of two times, the torque of the gear, the single one-way operation is 1, the failure probability is less than or equal to 1% is determined. When the load conditions are different in nature, work every day the number of hours is not at the same time, according to the work load of machine according to the classification of various factors are modified. The reducer two-way operation, will be seen P1N coefficient multiplied by 0.7 to 1, when the reliability KR reverse loads, reversing frequently, selected low for small value, and large value. Power down calculation: P2m=P2*KA*KS*KR, in which P2 is the working power; KA is the use factor; KS is the starting factor; KR is the reliable coefficient. (2) thermal power nuclear efficiency. Reducing the allowable heat power PG is applicable to the environmental temperature of 20 DEG C for 100% hour, continuous operation and power utilization (P2/P1N * 100%) is 100%, does not meet the above conditions, should be amended. (3) check the radial load on the shaft extension.

Drive to do a linear movement of the spiral, look at the net efficiency of the ball screw rod is relatively high, if the ball screw to make the counter revolution, is the nut with a one-way bearing vertical fixation, screw up and down reciprocating motion, so that you can do, if possible, wire rod length 40CM screw diameter, 8MM, vertical pressure 80N of the screw, choose the lead big nut can make the speed to 700 RPM in the under pressure?

But the rod itself can not be subjected to radial force, otherwise the life will be greatly reduced.Specific circumstances of specific analysis.

What are the functions of an automobile powertrain? What is the function of each part of it?

Composition and distribution of automobile transmission system:The composition and layout of the automobile powertrain vary with the type of engine, the location of the installation, and the use of the car. For example, off-road vehicles are mostly driven by four wheels, and in the transmission system, the actuators and other assemblies are added. As for the vehicle with front lead, there is no transmission shaft in its drive train.

What kind of lubricant does nylon transmission use?

Nylon parts are generally used in low light load occasions, and then products require higher cleanliness, generally do not need lubrication;

How to prevent the transmission shaft from breaking and falling off?

The automobile transmission shaft is an important part of transmitting the power of the transmission to the rear axle. If it breaks or falls out during the use, the capacity of the transmission shaft will be reducedTurning over vehicles easily will have serious consequences for safe driving. Therefore, in the use and maintenance of automobiles, corresponding measures must be takenApply to prevent the occurrence of such accidents. Causes of fracture and failure of transmission shaft:

The axial force of this drive eliminates the problem of how to do it! Thank you for the exam tomorrow

The axis III is under the action of gear 3, and its force direction is right. In order to counteract the force of the axis III, the worm gear 6 should be anticlockwise! The worm 5 and the rotation of the worm gear 6 also depend on the steering of the axle III.Therefore, to solve this problem, we must first determine the axis I steering, that is, bevel gear 1 steering.

This problem for a long time, a drive shaft with a key, how to fix the position after the rotation of concrete keyway, don't specify the rotation and rotation angle, through parallel or perpendicular to that location

What do I do if I want the slot above to be horizontal?