Raw Materials Los Angeles

Hot Products

Raw Materials for Refractory Long Nozzle Shape

REFRACTORY WHITE FUSED ALUMINA FOR ALUMINA BRICKS

High Alumina Cement Powder for Refractory

Raw Materials for Refractory Metal Bonded Unburned Sliding Gate

Raw Materials for Refractory Ladle Nozzle Pocket Brick

Raw Materials for Refractory Ladle Upper Nozzle & Collector Nozzle

Raw Materials for Refractory:CNBM Good Quality Bauxite Slagging Flux - Made in China

Calcined Kaolin Clay Powders for Refractory Fire Clay Bricks

TILTING KILN REFRACTORY BROWN FUSED ALUMINA

REFRACTORY GRADE CALCINED BAUXITE WITH COMPETITIVE PRICE

FAQ

What refractories can withstand high temperature above 2100 degrees?

Usually a dryer will not have such a high temperature. I do not know what you would use it for. Refractory cement coupled with quartz sand can work for 4 to 5 hours. So you can try cement coupled with corundum or superfine bauxite for better effect.

Fire rating of decoration materials

All light steel keel gypsum board is considered level A; if the wood finishes up to B2 grade fire rating depends on the proportion of the use of wood veneer and the proportion of this wood veneer fire grade, if the proportion of wood veneer is small,it can be considered level A

What's the fireproof specification for constrcution external wall thermal insulation materials?

Specification for constrcution external wall thermal insulation materials: Article 1 In order to implement the "State Council opinions on strengthening and improving fire prevention work" (state issued [2011] No. 46), to standardize fireproof design and application of external wall thermal insulation materials of newly constructed, renovated, and expanded civil buildings and to prevent and reduce fire of building external wall thermal insulation materials, this provision is made in accordance with relevant national technical standards and our province real situation. Article 2 When there is no cavity between external wall thermal insulation material for exterior wall and base wall and between decorative layers, the insulation system shall comply with the following provisions: (A) Residential buildings: 1. When the building is higher than 54m, combustion performance of the thermal insulation material shall be A level; 2. When the building is not higher than 54m,combustion performance of the thermal insulation material shall be at least B level. When using B1 level insulation materials, non-combustible materials should be used to make the protective layer, and a protective layer thickness of the first floor of the building should be not less than 10mm, the other floors not less than 5mm; incombustible?materials of more than 300mm height should be used to make horizontal fire barrier zone in every floor. (B) Other buildings in addition to residential buildings

Which brand of refractory fiber hard thermal insulation board is better?

One colleague said Huayou refractory fiber hard thermal insulation board is good. The size (mm): 600*400*60. refractory temperature: 1770 ~ 2000 ℃ (℃), and the price is 2850 yuan a ton.

who knows the requirements of refractory for forge furnace?

Here is the requirements of refractory for forge furnace: according to the chemical properties,casting fireproof materials are divided into three major categories: acidic, neutral and alkaline refractory materials. alkaline and neutral refractory materials are commonly used, such as alkaline magnesia-carbon bricks and burned magnesite bricks, magnesite-chrome bricks, magnesium-calcium brick, neutral high alumina brick, corundum brick, clay brick, etc., shapelessness materials include: castable refractory, ramming?mass, gunning mix, coating, dry vibrating materials and so on! Hope my answer can help you.

What are the main components of refractory cement?

SiO powder is often used. Ultra-fine powder refers to less than 1 / zm particles which are made by hydrolysis of ethyl silicate or made from recycled dust in the smelting process of ferro-silicon alloy. Non-cement castable refractory are castable refractory material which contains no cement instead it relies on the coagulation and combination by adding ultra-fine powder or sol (see refractory castable), and it is an amorphous material with high activity. Silica sol is made through Ion-exchange of sodium silicate after Na ions are removed. The easiest method is to prepare by reaction of aluminum metal with hydrochloric acid or alchlor. It is a thermodynamically unstable system which has certain requirements for ultra-fine powder and sol. It is different from non-cement refractory castable, Cr2zrOz and etc. It has low impurity content, and can bond with itself, so it has good binding strength. Ultrafine powder used in non-cement castables are SiO2, Al2O3, Cr2zrOz, etc. Such recycled SiO2 powder has an average particle diameter of 0.5 pm, therefore when adding the gelling agent (electrolyte), it can coagulate and give the products some bonding strength. Non-cement castable refractory is made up of refractory aggregate and powder and it is round. Since the use of superfine powder or sol as binder. The size of sol particles are of 0.1 ~ 1 m. Non-cement refractory castable takes oxide or synthetic compound ultra-fine powder or oxide sol-gel which is similar to the chemical composition of material in tungsten castable. There are several ways to prepare alumina sol. The sol used are mainly alumina oxide and silica sol. The surface area is large, and it helps to improve high-temperature structural strength. Non-cement castable refractories rely on oxide ultra-fine powder or sol to coagulate and combinate. It is a refractory castable (also known as chemical bonding castable) which uses chemical binder instead of cement for combination.

What effect does aluminium powder play in refractory bricks?

Aluminum powder can increase the high melting point of refractory refractory, while increasing material density, hardness and other changes in physical properties of aluminum powder in the application of unshaped refractories in the gas can be discharged in the material, prevent the refractory sudden warming occurred during the burst.

What are the use of fire-resistant material and admixture?

Generally speaking, there are several admixtures: 1. Water reducing agent. It can ensure basic refractory castable flow value and significantly reduce its water mixing amount sodium hexametaphosphate and sodium tripolyphosphate 2. Plasticizer. It can increase plastic refractory mixture and enhance the ability of bentonite clay mud material stress strain 3. Gelling agent. It can make the colloidal solution (or suspending liquid containing solid particles condensed gelling agent 4. Dispergator. It can turn condensation or reunion colloidal particles (particles) into sol or uniform dispersion suspended particles and make the thick colloid free stream sol said scattered coagulant peptizer 5. Coagulant. It can shorten the stereotypes refractories condense sclerosis NaOH Mars between aluminum hydroxide, etc. 6. Retarder. It can delay the stereotypes refractories condense sclerosis between citric acid tartaric acid, etc. 7. Delayed coagulant. It can make setting fire-resistant materials contain binder by set out the condensation hardening effect between calcium aluminate cement, etc. 8. Foaming agent. It can reduce the liquid surface of power to produce uniform stability as rosin soap bubble resin fat saponin and so on. 9. Antifoaming agent. It can make fast setting fire-resistant material mixing or shock in produce bubbles escape alcohol fatty acids, such as 10. Shrink agent can reduce or prevent the refractory materials used to produce contraction type heating said silicon powder stabilizer or volume expansion agent, etc. 11. Preservative. It can keep setting fire-resistant material stored on construction performance change or change oxalic acid citric acid, etc. 12. Inhibitors. It can inhibit stereotypes refractories ingredients contain iron or iron compounds and acidic reaction caused inflation to produce hydrogen bond CrO3 diacetone alcohol, etc. I hope it can help you.